User manual CRESTRON CLF-DIMRFB

[. . . ] Crestron CLF-DIMRFB infiNETTM Lamp Dimmer Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2006 Crestron Electronics, Inc. Crestron CLF-DIMRF infiNETTM Lamp Dimmer Contents InfiNETTM Lamp Dimmer: CLF-DIMRFB 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The LED will blink to indicate that the dimmer is in the SET mode. Refer to the following table for a list of available functions when the dimmer is operating in the SET mode. NOTE: Mode selection switch must be in the "SET" position for at least 0. 5s for unit to enter SET mode. SET Mode Functions EVENT SET mode entered (from OFF or RUN mode). ACTION Set the load to the preset level using a 0s fade* (or the minimum allowed fade). LED will blink at a steady rate while in this mode (refer to "LED Behavior" on page 17. Manually raise or lower the load using the current "ramp time"* parameter. The behavior will be alternating; releasing the button and pressing it again will cause the lights to ramp in the opposite direction. Switch to "RUN" mode to store preset. (User can abort any changes made in SET mode by switching unit OFF before returning to RUN. ) Foot switch is pressed. * Fade time and ramp time are parameters that can be changed in SIMPL Windows. Refer to the SIMPL Windows help file (F1) for details. Operations Guide ­ DOC. 6479 infiNETTM Lamp Dimmer: CLF-DIMRFB · 15 InfiNETTM Lamp Dimmer Crestron CLF-DIMRFB Special Functions Enter ACQUIRE Mode Before an infiNET device can be used on an infiNET network, it must first be acquired by a C2N-MNETGW gateway that is connected to a Cresnet network. NOTE: A dimmer can be acquired by only one gateway. To acquire a CLF-DIMRFB by a C2N-MNETGW, perform the following: 1. Put the C2N-MNETGW in the ACQUIRE mode, from the unit itself or from Toolbox, as described in the latest revision of the C2N-MNETGW guide (Doc. 6317) which is available from the Crestron website. NOTE: In environments where multiple gateways are installed, only one gateway should be in ACQUIRE mode at a time. Place the CLF-DIMRFB in the ACQUIRE mode by doing the following: a. Move the mode selection switch to the "OFF" position. Press and hold the foot switch, while sliding the mode switch to the "RUN" position. Continue holding the foot switch until you see the LED blink once. Now release the foot switch; the unit is now in ACQUIRE mode. NOTE: ACQUIRE mode does not actually start until the foot switch is released. [. . . ] Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. [. . . ]