User manual CRESTRON CLTI-1MC4 CLXI-1MC4

[. . . ] The ambient temperature must be 0°C to 40°C (32°F to 104°F). The relative humidity must be 0% to 90% (non-condensing). Terminal blocks are installed along the left side of singlewide enclosures and along the outside edges (left and right sides) of double-wide enclosures. Modules are installed along the right side of single-wide enclosures and side-by-side in the center of double-wide enclosures. [. . . ] Tighten to 4 Nm (2. 5 - 6. 0 mm2), 4. 5 Nm (10. 0 mm2), or 5. 1 Nm (16 ­ 25 mm2). Test the circuit for electrical faults by connecting LINE to OPEN 1. Switch on the circuit breaker and check that it does not trip and that the load connected to OPEN 1 is receiving power. Switch off the circuit breaker, remove the connection between LINE and OPEN 1, and repeat this step for CLOSE 1 and then sequentially for each OPEN and CLOSE motor connection. NEUTRAL GND GROUNDING TERMINAL BLOCK TO MOTOR 1 TO MOTOR 3 AREA FOR MODULE LOCATION LABEL TO MOTOR 2 TO MOTOR 4 LEFT SIDE WIRING LABEL TERMINAL BLOCK Wiring Diagram of the Terminal Block to the Feed and Load(s) (Right Side Double-wide Enclosures) 3. JUMPER 4. GND NEUTRAL HOT (FROM 10 OR 16 AMP CIRCUIT BREAKER) AREA FOR MODULE LOCATION LABEL TO MOTOR 2 TO MOTOR 4 GROUNDING TERMINAL BLOCK TERMINAL BLOCK RIGHT SIDE WIRING LABEL TO MOTOR 1 TO MOTOR 3 2 · Terminal Block & Module: CLTI- & CLXI-1MC4 Installation Guide ­ DOC. 6409 Crestron CLTI- & CLXI-1MC4 Module Installation CAUTION: Module contains electrostatic sensitive devices (ESDs); unit must be handled from metal chassis ­ do not touch PC board or components. NOTE: Modules are to be installed after enclosure has been completely wired. Refer to the terminal block installation procedure on page 2 for details. Use the four supplied self-tapping pan Phillips screws (8B x ¼-inch (6 mm) length) to secure the module to the enclosure. As shown in the wiring diagrams (next column), connect the wires from the module to the terminal block. Each wire exits the module directly in line with, and is the same color as, the terminal to which it should be connected. If the module is being installed above another module within the enclosure, attach the supplied module interconnect cable between the two modules. The illustration below depicts the area within a double-wide enclosure where the corners of four modules meet. Terminal Block & Module Wiring Diagram of the Terminal Block to the Module (Single-wide and Left Side Double-wide Enclosures) BROWN RED YELLOW RED YELLOW RED YELLOW RED YELLOW BLUE 2. ENLARGEMENT DETAIL: JUMPER ON BLUE SECTION REMAINS INSTALLED. 3. JUMPER INSTALLED NOTE: One wire on the module interconnect cable may be a different color from the rest. The color has no bearing on its orientation during installation. Use Module Interconnect Cable to Wire Module to Module MODULE INTERCONNECT CABLE ATTACHED CONNECTION NOT MADE Wiring Diagram of the Terminal Block to the Module (Right Side Double-wide Enclosures) BLUE YELLOW RED YELLOW RED YELLOW RED YELLOW RED BROWN 4. Turn on the circuit breaker and verify that the green PWR LED on the module lights and the breaker does not trip. ENLARGEMENT DETAIL: JUMPER ON BLUE SECTION REMAINS INSTALLED. JUMPER INSTALLED Installation Guide ­ DOC. 6409 Terminal Block & Module: CLTI- & CLXI-1MC4 · 3 Terminal Block & Module Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. For assistance in your local time zone, refer to the Crestron website (www. crestron. com) for a listing of Crestron worldwide offices. You can also log onto the online help section of the Crestron website to ask questions about Crestron products. First-time users will need to establish a user account to fully benefit from all available features. Crestron CLTI- & CLXI-1MC4 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. [. . . ] In no event shall CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for any claim made by a third party or made by the purchaser for a third party. CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. [. . . ]