User manual CRESTRON CLTI-4HSW4 CLXI-4HSW4

[. . . ] CAUTION: This equipment is for indoor use only and needs to be air-cooled. The ambient temperature must be 0°C to 40°C (32°F to 104°F). The relative humidity must be 0% to 90% (non-condensing). Terminal blocks are installed along the left side of singlewide enclosures and along the outside edges (left and right sides) of double-wide enclosures. [. . . ] Grounding terminal blocks are available in the cabinet for termination of ground wires. Tighten to 4 Nm (2. 5 - 6. 0 mm2), 4. 5 Nm (10. 0 mm2), or 5. 1 Nm (16 - 25 mm2). Test the circuit for electrical faults by turning on the circuit breaker and checking that the breaker does not trip and that power is delivered to the loads. TO LOAD 1 TO LOAD 2 TO LOAD 3 TO LOAD 4 GROUNDING TERMINAL BLOCK AREA FOR MODULE LOCATION LABEL LEFT SIDE WIRING LABEL TERMINAL BLOCK Wiring Diagram of the Terminal Block to the Feed and Load(s) (Right Side Double-wide Enclosures) BYPASS JUMPERS (*) FROM 10 OR 16 AMP CIRCUIT BREAKER NEUTRAL HOT 4 (*) NEUTRAL HOT 3 (*) NEUTRAL HOT 2 (*) NEUTRAL HOT 1 (*) GND 3. 4. RIGHT SIDE WIRING LABEL TERMINAL BLOCK AREA FOR MODULE LOCATION LABEL GROUNDING TERMINAL BLOCK TO LOAD 1 TO LOAD 2 TO LOAD 3 TO LOAD 4 2 · Terminal Block & Module: CLTI- & CLXI-4HSW4 Installation Guide ­ DOC. 6412 Crestron CLTI- & CLXI-4HSW4 Module Installation CAUTION: Module contains electrostatic sensitive devices (ESDs); unit must be handled from metal chassis ­ do not touch PC board or components. NOTE: Modules are to be installed after enclosure has been completely wired. Refer to the terminal block installation procedure on page 2 for details. Use the four supplied self-tapping pan Phillips screws (8B x ¼-inch (6 mm) length) to secure the module to the enclosure. As shown in the wiring diagrams (next column), connect the wires from the module to the terminal block. Each wire exits the module directly in line with, and is the same color as, the terminal to which it should be connected. If the module is being installed above another module within the enclosure, attach the supplied module interconnect cable between the two modules. The illustration below depicts the area within a double-wide enclosure where the corners of four modules meet. Terminal Block & Module NOTE: Before the two-position bypass jumpers, shown in the illustration, are removed, the Crestron Professional Automation Computer (PAC2), which provides control to the system, should be properly connected and contain a valid program to provide control of the module. Wiring Diagram of the Terminal Block to the Module (Single-wide and Left Side Double-wide Enclosures) BROWN RED BLUE BLUE BROWN RED BLUE BLUE BROWN RED BLUE BLUE BROWN RED BLUE BLUE 2. ENLARGEMENT DETAIL: BYPASS JUMPERS ON BROWN AND RED SECTIONS OF TERMINAL BLOCK HAVE BEEN REMOVED AFTER LOOSENING ALL SCREWS. JUMPER ON BLUE SECTIONS ARE NOT REMOVED. 3. NOTE: One wire on the module interconnect cable may be a different color from the rest. The color has no bearing on its orientation during installation. Use Module Interconnect Cable to Wire Module to Module MODULE INTERCONNECT CABLE ATTACHED CONNECTION NOT MADE JUMPERS INSTALLED BYPASS JUMPERS REMOVED Wiring Diagram of the Terminal Block to the Module (Right Side Double-wide Enclosures) BLUE BLUE RED BROWN BLUE BLUE RED BROWN BLUE BLUE RED BROWN BLUE BLUE RED BROWN 4. Turn on the circuit breaker and verify that the green PWR LED on the module lights, the breaker does not trip, and power is delivered to the loads. Turn off the circuit breaker and remove the twoposition bypass jumpers on the brown and red sections of the terminal block. The jumpers on the blue sections of the terminal block remain installed. Refer to the figures in the next column for a close-up of the jumpers. ENLARGEMENT DETAIL: BYPASS JUMPERS ON BROWN AND RED SECTIONS OF TERMINAL BLOCK HAVE BEEN REMOVED AFTER LOOSENING ALL SCREWS. JUMPER ON BLUE SECTIONS ARE NOT REMOVED. 5. BYPASS JUMPERS REMOVED JUMPERS INSTALLED Installation Guide ­ DOC. 6412 Terminal Block & Module: CLT- & CLX-4HSW4 · 3 Terminal Block & Module 6. If the program is not running yet, loads can be tested by using Local Mode. Crestron CLTI- & CLXI-4HSW4 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. [. . . ] This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if any. CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended, or if it has been subjected to misuse, accidental damage, modification, or improper installation procedures. Furthermore, this warranty does not cover any product that has had the serial number altered, defaced, or removed. [. . . ]