User manual CRESTRON CLW-DIM CLW-DIMS CLW-SLVD

[. . . ] CLW-DIM, DIMS, & SLVD(W/A/B) Introduction Features and Functions The CLW-DIM (-DIM) is a stand-alone wall box dimmer that can also act as a Cresnet® device that reports to a Crestron® control processor. The CLW-DIM has four preset lighting levels that can be adjusted (refer to note below). The CLW-DIM also includes two isolated, nonpolarized Cresnet wires (plus a ground wire) for connecting to the Cresnet network over a twisted pair wire with shield. NOTE: The four preset levels are noted as Button 1High, Button 1-Low, Button Preset 2, and Button Preset 3. [. . . ] The following charts provide derating information for various applications. Derating Information for Incandescent and Tungsten Halogen Applications Part No Side Removed Number -DIM -DIMS -SLVD 1000W 1000W One Side Removed 600W 600W No Derating Necessary Two Sides Removed 400W 400W · · Derating Information for Magnetic Low Voltage Applications* Part Number -DIM -DIMS No Side Removed 1000VA/750W 1000VA/750W One Side Removed 600VA/450W 600VA/450W Two Sides Removed 400VA/300W 400VA/300W -SLVD No Derating Necessary * VA ratings are for input power to the transformer. If you do not know the input power requirement of the transformer, use the bulb's wattage rating to determine proper rating. 2. To remove a side section, bend the side section back and forth with a pair of pliers until the section breaks off from the mounting plate. Use a file or sandpaper to remove any excess metal. Prewire for Master Application Each device has two Class 2 low voltage wires (plus a ground wire) that provide a Cresnet connection over Stand Alone Wall Box Dimmer: CLW-DIM, DIMS, & SLVD · 3 Installation Guide ­ DOC. 5995B CLW-DIM, DIMS, & SLVD(W/A/B) shielded twisted-pair to a Crestron control system. These wires are routed to the bottom of the device for connection outside of the wallbox. The low voltage wires are pulled from each device location to the Crestron control system, a Crestron power supply, a Crestron C2N-NPA8, or a Crestron connection block device. Use #22 AWG, twisted, shielded, 2-conductor wire. Wiring can be daisy chained, T-tapped, or home run back to the control system. Refer to the following wiring diagram. Wiring Diagram of CLW device to Cresnet 1. 2. Turn power off at the circuit breaker. If installing multiple dimmers (-DIM or -DIMS), note the serial number on each device and make sure they are being installed in the proper location. Pull Class 2 low voltage wires through a hole in the drywall located outside of the electrical box, to the Crestron control system, a Crestron power supply, a Crestron C2N-NPA8, or a Crestron connection block device. Leave wires outside of the wallbox for connection to the -DIM or -DIMS. 3. NOTE: Alternate wiring methods may be used for the Class 2 wiring connection. Refer to section 725-55, Part D of the 2002 National Electric Code. Wire the device for the appropriate application. Choose either "CLW-DIM / CLW-DIMS Wiring" or "CLW-DIMS with CLW-SLVD Wiring", shown on this page and the following page. NOTE: The GRAY (Cresnet) wires are not polarized. These wires can be connected to either the Y or Z line on a Cresnet port. NOTE: The BLACK wire (Cresnet ground) should not be grounded with the GREEN (Ground) wire on the -DIM/-DIMS/-SLVD. NOTE: Crestron recommends using Crestron's CresnetDM cable for connecting the -DIM and -DIMS to the Cresnet network. NOTE: Alternative wiring methods can be obtained from the Dealer/Tech Resources | Design Center section of the Crestron website (http://www. crestron. com/dealertech_resources/design_center/hot_design_tips_and_ diagrams/tech_sales_tips/). CLW-DIM / CLW-DIMS Wiring NOTE: The -DIM and-DIMS require a neutral wire for operation. If no neutral is present, contact a licensed electrician for installation or contact Crestron customer service for alternative wiring options. The following wiring diagram illustrates installation of the -DIM or -DIMS. Wiring Diagram for CLW-DIM or CLW-DIMS (without CLW-SLVD) Hot BLUE (-DIMS ONLY) Installation NOTE: The -DIMS must be installed in the same wallbox that contains the connections to the load. NOTE: The -DIM, -DIMS, and -SLVD require a neutral wire for operation. [. . . ] Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. In the event repairs are found to be nonwarranty, return freight costs shall be paid by the purchaser. 2. 3. CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in materials and workmanship under normal use for a period of three (3) years from the date of purchase from CRESTRON, with the following exceptions: disk drives and any other moving or rotating mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen display and overlay components are covered for 90 days; batteries and incandescent lamps are not covered. This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON dealer. [. . . ]