User manual CRESTRON CLW-DIM1 DIMS1 SLVD1

[. . . ] CLW-DIM1, DIMS1, & SLVD1(W/A/B) Introduction Features and Functions The CLW-DIM1 (-DIM1) is a stand-alone wall box dimmer that can also act as a Cresnet® device that reports to a Crestron® control processor. The CLW-DIM1 has two preset lighting levels that can be adjusted (refer to note below). The CLW-DIM1 also includes two isolated, non-polarized Cresnet wires (plus a ground wire) for connecting to the Cresnet network over a twisted pair wire with shield. NOTE: The two preset levels are noted as Preset 1-High and Preset 1- Low. [. . . ] When installing a -DIM1 or a -DIMS1 without a slave, follow the instructions in "Wiring a -DIM(S)1 (No Slaves)". If wiring a -DIMS1 with a -SLVD1, refer to Derating Information for Magnetic Low Voltage Applications* Part Number -DIM1 -DIMS1 -SLVD1 * No Side Removed 1000VA/750W 1000VA/750W One Side Removed 600VA/450W 600VA/450W No Derating Necessary Two Sides Removed 400VA/300W 400VA/300W VA ratings are for input power to the transformer. If you do not know the input power requirement of the transformer, use the bulb's wattage rating to determine proper rating. 2. To remove a side section, bend the side section back and forth with a pair of pliers until the section breaks off from the mounting plate. Splice the gray wires of the -DIMS1 to the Class 2 low voltage wires connected to the Crestron control system or a Crestron connection block device. Push the wires and the splices into a hole in the drywall to provide the necessary separation. Wiring a -DIM(S)1 (No Slaves) The following describes the installation of a stand-alone -DIM1 or -DIMS1. Pull Class 2 low voltage wires through a hole in the drywall located outside of the electrical box, to the Crestron control system or a Crestron connection block device. Leave wires outside of the wallbox for connection to the -DIM1 or -DIMS1. NOTE: Alternate wiring methods may be used for the Class 2 wiring connection. Refer to section 725-55, Part D of the 2002 National Electric Code. Wire the dimmer as shown in Figure 1 on page 8. NOTE: The RED (Load) and BLACK (Hot) wires are #14 AWG. The BLUE (Slave) and WHITE (Neutral) wires are #18 AWG. The BLACK wire (Cresnet ground) paired with the GRAY (Cresnet) wires is #22 AWG. NOTE: Since the -DIMS1 is installed without a -SLVD1, the BLUE lead (Slave) should be capped. Alternative Wiring For situations where a neutral is not present or other scenarios that may be encountered during installation, refer to the "Stand-Alone Installations" section of "Appendix: Wiring Diagrams" on page 8. Splice the gray wires of the -DIM1 or -DIMS1 to the Class 2 low voltage wires connected to the Crestron control system or a Crestron connection block device. Push the wires and the splices into a hole in the drywall to provide the necessary separation. Push all power wires back into the wallbox and fasten the device to the wallbox with the provided screws. Restore power at the circuit breaker. 5. 6. 6250A Stand Alone Wall Box Dimmer: CLW-DIM1, DIMS1, & SLVD1 · 5 CLW-DIM1, DIMS1, & SLVD1(W/A/B) 5. Push all power wires back into the wallbox and fasten the devices to their respective wallboxes with the provided screws. The lighting level will stop at maximum brightness (100%) if the lighting level was ramping up or minimum brightness (0%) if the lighting level was ramping down. [. . . ] Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ]