User manual CRESTRON CLW-SW CLW-SWS CLW-SLVS

[. . . ] CLW-SW, SWS, & SLVS(W/A/B) Introduction Features and Functions The CLW-SW (-SW) is a stand-alone wall box switch that can also act as a Cresnet® device that reports to a Crestron® control processor. The -SW includes two isolated, non-polarized Cresnet wires (plus a ground wire) for connecting to a Cresnet system over a twisted pair wire with shield. The CLW-SW features a three-position mode selection switch. Refer to "Operating Buttons and Switches " on page 5 for more information. [. . . ] If you do not know the input power requirement of the transformer, use the bulb's wattage rating to determine proper rating. Derating Information for Fluorescent/HID Applications Part Number -SW -SWS -SLVS No Side Removed 8A 8A One Side Removed 5A 5A No Derating Necessary Two Sides Removed 3A 3A Derating Information for General Purpose Fans Part Number -SW -SWS -SLVS No Side Removed 3A 3A One Side Removed 3A 3A No Derating Necessary Two Sides Removed 3A 3A 2. To remove a side section, bend the side section back and forth with a pair of pliers until the Installation Guide ­ DOC. 6134B Stand Alone Wall Box Switch: CLW-SW, SWS, & SLVS · 3 CLW-SW, SWS, & SLVS(W/A/B) section breaks off from the mounting plate. Use a file or sandpaper to remove any excess metal. NOTE: New installations should be checked for short circuits prior to installing the -SW, -SWS, or -SLVS. With power off, close the circuit and restore power. If the load does not work or a breaker trips, check and correct the wiring or fixture (if necessary). Install the -SW, -SWS, or -SLVS only when the short is no longer present. The warranty is void if the -SW, -SWS, or -SLVS is installed and operated with a shorted load. If installing multiple switches (-SW or -SWS), note the serial number on each device and make sure they are being installed in the proper location. Pull Class 2 low voltage wires through a hole in the drywall located outside of the electrical box, to the Crestron control system, a Crestron power supply, a Crestron C2N-NPA8, or a Crestron connection block device. Leave wires outside of the wallbox for connection to the -SW or -SWS. Prewire for Master Application Each device has two Class 2 low voltage wires (plus a ground wire) that provide a Cresnet connection over shielded twisted-pair to a Crestron control system. These wires are routed to the bottom of the device for connection outside of the wallbox. The low voltage wires are pulled from each device location to the control system, a Crestron power supply, a Crestron C2N-NPA8 Poll Accelerator, or a Crestron connection block device. Use # 22 AWG, twisted, shielded, 2-conductor wire. Wiring can be daisy chained, T-tapped, or home run back to the control system. Refer to the following wiring diagram. Wiring Diagram of CLW device to Cresnet 3. NOTE: Alternate wiring methods may be used for the Class 2 wiring connections. Refer to section 725-55, Part D of the 2002 National Electric Code. Wire the device for the appropriate application. Choose either "CLW-SW / CLW-SWS Wiring" or "CLW-SWS with CLW-SLVS Wiring", shown on this page and the following page. NOTE: The GRAY (Cresnet) wires are not polarized. These wires can be connected to either the Y or Z line on a Cresnet port. NOTE: The BLACK wire (Cresnet ground) should not be grounded with the GREEN (Ground) wire on the -SW/-SWS/-SLVS. NOTE: Crestron recommends using Crestron's CresnetDM cable for connecting the -DIM and -DIMS to the Cresnet network. CLW-SW / CLW-SWS Wiring NOTE: The -SW and -SWS require a neutral wire for operation. [. . . ] CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. In the event repairs are found to be nonwarranty, return freight costs shall be paid by the purchaser. Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. For assistance in your local time zone, refer to the Crestron website (www. crestron. com) for a listing of Crestron worldwide offices. [. . . ]