User manual CRESTRON CN-TVAV

[. . . ] This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Crestron CN-TVAV Programmable TV/AV Controller Contents Programmable TV/AV Controller: CN-TVAV Description Functional Description Physical Description Leading Specifications Setup Cresnet Modular Cabling Cable Configuration for Programming Programming Cable Fabrication Specifications Special Considerations for Using the RS-232 Port for Uploading Programs Cable Configuration for Normal Operation Identity Code Loading Crestron Control Software Installing Crestron Development Tools Initial Setup File Types Obtaining Communications Troubleshooting Communications Loading the System Program Updating the CN-TVAV Programming with SIMPLTM Windows® or SIMPL+ Programming Modes Typical Programming Application Example Programs Problem Solving Troubleshooting Internal Fuse Replacement Further Inquiries Future Updates Return and Warranty Policies Merchandise Returns / Repair Service CRESTRON Limited Warranty 1 1 1 2 6 7 7 8 9 10 11 12 13 13 14 15 18 20 21 22 24 25 28 29 30 30 30 33 33 34 34 34 Operations Guide - DOC. 5722B Contents · i Crestron CN-TVAV Programmable TV/AV Controller Programmable TV/AV Controller: CN-TVAV Description Functional Description The CN-TVAV is a multi-purpose television/audio-visual (TV/AV) device controller that is compatible with SIMPLTM Windows® and can be used as a standard Crestron remote control system (herein referred to as the Cresnet system) peripheral or as a "smart" peripheral. As a standard Cresnet system peripheral, the CN-TVAV can be added as a Cresnet network device to a host Crestron control system with all logic, infrared (IR) drivers, and serial strings stored in the control system programming logic. [. . . ] Ops Subdirectory - The files (described in the table below) in this subdirectory contains the CN-TVAV operating system with which the program was tested. Ensure that the operating system version currently loaded is equal to or newer than the version included here, so that the program runs properly. For help with uploading an operating system, refer to "Updating the CN-TVAV" on page 22. File Types in Ops Subdirectory FILE TYPE . upz DESCRIPTION This is a control system file. For more information regarding these files, refer to "Updating the CV-TVAV". Programs Subdirectory - The files (described in the table below) in this subdirectory contain the system program. This is the main program that loads into the CN-TVAV and determines the exact functionality. File Types in Programs Subdirectory FILE TYPE . asv . bin . dip DESCRIPTION SIMPL Windows auto-save file. This is the executable code for the CN-TVAV. This is the default IP Table that contains the IP addresses of all of the ethernet devices in the system. It is generated when the program is compiled. This file contains information required by Test Manager (see SIMPL Windows help for more information) for debugging programs in realtime. It is generated each time the program is compiled. This is the SIMPL-C file that is generated from the SMW file when a program is compiled. In SIMPL Windows version 1. 18 or lower, this file is what actually gets compiled into the BIN file. In versions after 1. 18, this file may or may not be generated and but is not required. It contains the source code for the main system program. SIMPL Windows program backup file. . sig . smp . smw . sm2 Userdb Subdirectory - The files (described in the table below) in this subdirectory is a user database IR driver that is needed to interface with certain IR-controlled devices. This driver differs from Crestron database IR drivers in that the former are included as part of a Crestron Database. File Types in Userdb Subdirectory FILE TYPE DESCRIPTION This is a user IR driver file. It is needed during the convert/compile process in order to properly compile the program. If recompilation of the program is necessary, use the Import Program option or copy any IR files received into the default user database directory (see SIMPL Windows help for more information). Alternatively, set the SIMPL Windows userdb directory to the directory where the macros exist. (In SIMPL Windows, this is accomplished from the Directories tab by selecting Edit | Preferences. ) . ir 16 · Programmable TV/AV Controller: CN-TVAV Operations Guide - DOC. 5722B Crestron CN-TVAV Programmable TV/AV Controller Usrmodule Subdirectory - The files (described in the table below) in this subdirectory are user modules, or special sub-programs that are integral parts of the main program. These differ from Crestron modules in that the former are supplied as part of the development software. File Types in Usrmodule Subdirectory FILE TYPE DESCRIPTION This is a user module file. [. . . ] Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. [. . . ]