User manual CRESTRON CNIRHT-15 30

[. . . ] CRESTRON CNRFHT-15/30 & CNIRHT-15/30 Hand-Held Wireless Transmitters TABLE OF CONTENTS PAGE 1 1 1 1 1 2 3 3 3 3 3 4 4 6 6 6 7 10 11 11 DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CNRFHT-15/30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CNIRHT-15/30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For RF devices the ID CODE is referred to as RF ID. For IR devices the ID CODE is referred to as IR ID. There are 256 possible two-digit hexadecimal alphanumeric codes ranging from 00 to FF. To maintain code diversity within the CRESNET II system, use codes between 10 and FE for the transmitters. NOTES 1. The ID CODE on the CNRFHT and CNIRHT is factory set to 20. Do not confuse RF/IR ID with network (NET) ID. To set an ID CODE complete the following steps. Position the unit button-side down so the battery compartment is accessible. Remove four screws from the unit (two screws are located within the battery compartment). Gently lift the rear cover off the unit. 5. Refer to figure 3 and locate an eight-position SIP switch on the printed circuit board. Switches labeled 1 through 4 represent the least-significant digit or letter of the ID CODE. Switches labeled 5 through 8 represent the most-significant digit or letter of the ID CODE. SV8 2F Enlarged 8- Position SIP Switch (set to 20) Figure 3. SIP Switch Location REMOTE CONTROL SYSTEMS 4 123 4 56 Rear Cover and Battery Cover Removed. 123 4 56 78 78 SV8 2F DOC. 8054C CRESTRON CNRFHT-15/30 & CNIRHT-15/30 6. Hand-Held Wireless Transmitters Refer to table 3 and translate the ID CODE two-digit hexadecimal number or letter into an eight-digit SIP switch code. NOTES 1. The ID CODE of the unit is factory set to 20. This hexadecimal setting corresponds to an eight-digit SIP switch code of 00000100, with respect to SIP switches 1 through 8. A "1" in the table indicates that the switch should be set in the direction of the arrow head located on the SIP switch. A "0" in the table above indicates that the switch should be set in the opposite direction of the arrow head. Table 3. CNRFHT and CNIRHT SIP Switch Settings Hexadecimal NUMBER OR LETTER 0 1 2 3 4 5 6 7 8 9 A B C D E F 7. 8 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 Most-Significant SIP Switch Digit 7 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 6 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 5 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 4 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 Least-Significant SIP Switch Digit 3 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 2 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Use a small screwdriver or a small pair of pliers and adjust the switch, appropriately. Ensure all screw standoffs are properly situated and place the rear cover onto the unit. 9. Secure the rear cover by tightening the four screws. [. . . ] CORRECTIVE ACTION Install new battery. Intermittent response during transmission. No response from CRESNET II system. Depress and hold any button until unit transmits. Refer to causes when LED does not illuminate. Refer to corrective action when LED does not illuminate. Refer to Installation/Setup for tuning instructions. [. . . ]