User manual CRESTRON CNIRHT-MM

[. . . ] This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Crestron CNIRHT-MM 30 Function Hand-Held IR Transmitter Contents 30 Function Hand-Held IR Transmitter: CNIRHT-MM 1 Description Functional Description Physical Description Leading Specifications Transmitter ID Code Set or Display Transmitter ID via Keypad Buttons Set Transmitter ID via CNIDC and PC Programming with SIMPLTM Windows® or SIMPL+ Configure CNIRHT-MM Program CNIRHT-MM Symbol Example Program Problem Solving Troubleshooting Further Inquiries Future Updates Return and Warranty Policies Merchandise Returns / Repair Service CRESTRON Limited Warranty 1 1 1 2 3 4 5 8 8 9 12 12 12 13 13 14 14 14 Operations Guide - DOC. 8171 Contents · i Crestron CNIRHT-MM 30 Function Hand-Held IR Transmitter 30 Function Hand-Held IR Transmitter: CNIRHT-MM Description Functional Description The CNIRHT-MM is a 30 function, hand-held infrared (IR) transmitter designed to work with the CEN-TVAV and/or CN-TVAV. By setting an IR transmitter identification (ID) code in the CNIRHT-MM and using the keypad buttons, any television or audio-visual (TV/AV) device attached to the CEN/CN-TVAV may be controlled remotely. [. . . ] From the Viewport Functions menu, select Set Transmitter ID as shown below. Select Set Transmitter ID 6 · 30 Function Hand-Held IR Transmitter: CNIRHT-MM 9V BATTERY Operations Guide - DOC. 8171 Crestron CNIRHT-MM 30 Function Hand-Held IR Transmitter 8. When the Set Transmitter ID window (shown below) appears, enter a two-digit hexadecimal number ranging from 10 to FE and click OK. "Set Transmitter ID" Window 9. Making sure that the IR probe of the CNIDC remains positioned over the CNIRHT-MM sensor, lift and rotate the CNIRHT-MM so that the front LED is visible. As shown below, observe the Transmitter ID window and then click OK to set the Transmitter ID. Click OK in "Transmitter ID" Window 11. When the LED of the CNIRHT-MM stops flashing, the Transmitter ID has been set. Remove the IR probe of the CNIDC from the sensor and the LED flashes three times to indicate the unit has resumed normal operating mode. Re-install the battery compartment cover onto the battery compartment. At PC, exit the Viewport and SIMPL Windows or VT Pro-e. Disconnect the 9-pin connector of the CNIDC from the COM port on the PC. Operations Guide - DOC. 8171 30 Function Hand-Held IR Transmitter: CNIRHT-MM · 7 30 Function Hand-Held IR Transmitter Crestron CNIRHT-MM Programming with SIMPLTM Windows® or SIMPL+ SIMPL (Symbol Intensive Master Programming Language) is an easy-touse programming language that is completely integrated and compatible with all Crestron system hardware. The objects that are used in SIMPL are called symbols. SIMPL Windows offers drag and drop functionality in a familiar Windows® environment. SIMPL Windows is Crestron's software for programming Crestron control systems. It provides a well-designed graphical environment with a number of workspaces (i. e. , windows) in which a programmer can select, configure, program, test, and monitor a Crestron control system. NOTE: The following descriptions assume that the reader has knowledge of SIMPL Windows. If not, refer to the extensive help information provided with the software. Within a Cresnet system, a CEN/CN-TVAV may be accessed as a Local Processing peripheral, a Remote Processing peripheral, or a "mixed mode" peripheral. To utilize the CNIRHT-MM, a SIMPL Windows program must be loaded into a Local Processing or Mixed Mode CEN/CN-TVAV. If using a Mixed Mode CEN/CN-TVAV, the program must also be loaded into the host control system. Refer to the documentation supplied with the CEN/CN-TVAV for further details. Configure CNIRHT-MM Program To create a program with a CNIRHT-MM in the Configuration Manager of SIMPL Windows, refer to the table on the next page for initial configuration information. NOTE: Multiple CNIRHT-MMs may be used with a single CEN/CNTVAV. [. . . ] Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. [. . . ]