User manual CRESTRON CNPCI-8

[. . . ] The CNPCI-8 has a 9-pin connector for attaching eight local inputs. Control System Update File 2-Series Control System CEN/CN-TVAV CNMSX-AV/PRO CNRACKX/-DP ST-CP Version C2-2. 000. CUZ or later Version 5. 10. 13V. UPZ or later Version 5. 01. 35X. UPZ or later Version 5. 01. 35W. UPZ or later Version 4. 02. 04S. UPZ or later 0°C to 40°C (32°F to 104°F) 10 to 90% Relative Humidity (Non-Condensing) Height: 15. 0 in (38. 1 cm) Width: 8. 0 in (20. 3 cm) Depth: 2. 5 in (6. 4 cm) Weight: 7. 2 lbs (3. 3 kg) Operating Temperature and Humidity Dimensions and Weight Operation Providing a closure from ground (G input pin) to any of the input pins 1-8 provides an input to the Cresnet system. These inputs can be programmed to control the CNPCI-8 relays and/or other control system functions. A SIMPL signal, which is driven by a local input, remains high for as long as the closure to ground exists on the corresponding input pin. When the signal driving a relay goes high, the corresponding relay activates. [. . . ] Illumination indicates that the SIMPL Windows program currently loaded has a network device defined at the same Net ID as the CNPCI-8. Operations Guide ­ DOC. 8028C 03. 04 Specifications subject to change without notice. Identity Code All equipment and user interfaces within Cresnet require a unique identity code (Net ID). These codes are two-digit hexadecimal numbers from 03 to FE. The Net ID of each unit must match an ID code specified in the SIMPL Windows program. To set the Net ID, locate two miniature rotary switches, identified as H and L. These 16-position hexadecimal switches can be set to 0 through F. Using a small screwdriver, rotate the arrow in the center of the switch marked H to point to the first (or most-significant) digit of the specified Net ID. Set the switch marked L to the second (least-significant) digit of the specified Net ID. Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888. CRESTRON Fax: 201. 767. 7576 www. crestron. com Power Control Interface: CNPCI-8 CNPCI-8 Wiring 20A NEUTRAL TO LOAD Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. In the event repairs are found to be nonwarranty, return freight costs shall be paid by the purchaser. CIRCUIT #7 LINE LOAD CIRCUIT #8 LINE LOAD CIRCUIT #6 LINE LOAD 2. CONTACT RATING: 20A UP TO 277VAC ALL CONTACTS SPST NORMALLY OPEN ALL CONTACTS FULLY ISOLATED THIS PRODUCT USES ELECTRO-MECHANICAL RELAYS FOR SWITCHING THE LOADS. CERTAIN ELECTRONIC BALLASTS HAVE VERY HIGH INRUSH CURRENTS WHICH MAKE THEM INCOMPATIBLE WITH ELECTRO-MECHANICAL RELAYS. CHECK WITH BALLAST MANUFACTURER FOR COMPATIBILITY. CIRCUIT #3 LINE LOAD CIRCUIT #4 LINE LOAD CIRCUIT #5 LINE LOAD 3. CIRCUIT #1 LINE LOAD CIRCUIT #2 LINE LOAD CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. [. . . ] This warranty statement supercedes all previous warranties. Trademark Information All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered trademark of Microsoft Corporation. Windows95/98/Me/XP and WindowsNT/2000 are trademarks of Microsoft Corporation. CRESTRON NET POWER MODEL: CLCI-8 / CNPCI-8 R LISTED 48D0 INDUSTRIAL CONTROL EQUIPMENT NET 24 Y Z G LOCAL INPUTS 1 2 3 4 5 6 7 8 G ID CODE H L TO CRESNET SYSTEM COMPUTER (REFER TO NETWORK INTERCONNECT DRAWING) Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. For assistance in your local time zone, refer to the Crestron website (www. crestron. com) for a listing of Crestron worldwide offices. [. . . ]