User manual CRESTRON CNSNET

[. . . ] Dimensions and weight are approximations rounded to the nearest tenth unit. Table 1. Leading Specifications SPECIFICATION Power Requirements CRESNET II Workshop CRESNET II Operating System Compiler Dimensions & Weight DETAILS 3 Watts Version 4. 31 (standard released version) 3. 09. 17 or later (standard manufacturing version) 3. 06. 06 or later (standard release version) Height: 1. 4 in (3. 7 cm) Width: 3. 6 in (9. 2 cm) Depth: 7. 1 in (17. 9 cm) Weight: 1. 1 lb (0. 5 kg) As of the date of manufacture, the unit has been tested and found to comply with specifications for CE marking. CONTROLS AND INDICATORS: Controls There are no user accessible control mechanisms on the CNSNET. Indicators There are two LED indicators located on the CNSNET, refer to figure 2. REMOTE CONTROL SYSTEMS 2 DOC. 8085 CRESTRON CNSNET ID SEL PC Interface The red LED illuminates when communication between the CRESNET II system and the CNSNET is established. Illumination indicates that the identity code of the CNSNET matches the identity code of a network unit in the SIMPL program currently running in the CRESNET II system. PWR The green LED illuminates when 24 volts is supplied to the CNSNET over the network. INSTALLATION/SETUP: Software Installation After creating customized control screens for a specific project with VisionPC/Create, use the "Create Install" utility to develop VisionPC/Control disk(s). [. . . ] Complete the following steps in the order provided to ensure proper installation of the unit. Before making any connections, review latest revision of network interconnection drawing (Doc. Connect the network female connector to the 4-pin male connector at the front of the CNSNET. Network termination points are available at the control system power supply. Network units may also be daisy-chained together. Refer to the latest revision of the CRESNET II reference manual section on CNPWS power supplies for wire gauge specifications and connection details. Connect one end of the seven foot telephone cable to the CNSNET panel marked RS-232. Figure 4 illustrates a detailed drawing for the cable. Attach the RJ11 to DB9S adaptor to the loose end of the telephone cable. Attach the nine-pin connector to the proper COM port on the PC. Apply power to the CNSNET and observe illumination of the red LED marked ID SEL and green LED marked NET PWR on the unit's panel. Identity Code Each device on the CRESNET II network requires a unique identity code (ID CODE). These codes consist of a two-digit hexadecimal number ranging from 03 to FE. The ID CODE of each unit must match the ID CODE specified in the "NET. ID" statement of the CRESNET II SIMPL-I program in order for the device to be addressed properly. The CNSNET ID CODE is not manually set on the unit itself. Instead, the CNSNET ID CODE is assigned in VisionPC/Create and can be modified during installation of VisionPC/Control disk(s). REMOTE CONTROL SYSTEMS 4 DOC. 8085 CRESTRON CNSNET RJ11 PC Interface DB9F 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 Figure 4. CNSNET, RJ11 RS-232 Port to 9-Pin Computer Port Cable PROGRAMMING: A basic touchpanel SIMPL program is illustrated in figure 5. An example follows the figure to illustrate the CRESNET II screen displays for touchpanel signal name assignment. The screen displays illustrated in this example are accessible from the "Define Network" section of the SIMPL-I Menu in the CRESNET II Workshop. CTP-3000 INTERLOCK i1 i2 i3 i4 relay1 relay2 relay3 relay4 S-1 o1 o2 o3 o4 relay1_fb relay2_fb relay3_fb relay4_fb NET. ID:03 Figure 5. CNSNET, SIMPL Program REMOTE CONTROL SYSTEMS 6 DOC. 8085 CRESTRON CNSNET System PF: Net ID 03: 04: 05: 06: 07: 08: 09: 0A: TAB to select entries F2-Detail ESC to Def Equip Define Network 4. 5 Description PC Interface Net PF: P. F. 3. 0 Net Device CTP-3000 PgUp/PgDn to find ID F3-Display Signals F1=Help Net ID: 03 CTP-3000 Command Center Touch Panel P. F. : 3. 0 JOIN# BUTTON SIGNAL NAMES 1: relay1 2: 3: 4: 5: 6: 7: 8: 10. [. . . ] Incandescent lamps are completely excluded from Crestron's Limited Warranty. CRESTRON shall, at its option, repair or replace any product found defective without charge for parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. CRESTRON shall not be liable to honor warranty terms if the product has been used in any application other than that for which it was intended, or if it has been subjected to misuse, accidental damage, modification, or improper installation procedures. [. . . ]