User manual CRESTRON CNWM-LU12

[. . . ] Crestron CNWM-LU12 Lutron® Keypad Contents Lutron® Keypad: CNWM-LU12 Description Functional Description Physical Description Leading Specifications Setup Network Wiring Keypad Installation Identity Code Programming with SIMPLTM Windows® CNWM-LU12 Symbol How the Example Program Works Problem Solving Troubleshooting Further Inquiries Return and Warranty Policies Merchandise Returns / Repair Service CRESTRON Limited Warranty 1 1 1 1 3 4 4 5 6 6 7 7 9 9 9 10 10 10 Operations & Installation Guide - DOC. 8150 Contents · i Crestron CNWM-LU12 Lutron® Keypad Lutron Keypad: CNWM-LU12 ® Description Functional Description The Lutron® Keypad, CNWM-LU12, is a 12 button keypad that is part of the Crestron HomeTM total control system. It features a faceplate and buttons that match the style and colors of Lutron's GRAFIK EYE TM or HomeworksTM systems. The CNWM-LU12 is a standard Cresnet device, may be programmed as desired using SIMPLTM Windows®, and does not require a ST-LT interface module. [. . . ] Position the adapter so that the mounting bracket holes align with the assembly mounting holes, and CAREFULLY push the button assembly and adapter together. Make sure that the Cresnet system power is turned OFF. CAUTION: The CNWM-LU12 faceplate is a two-piece assembly and is shipped with the faceplate installed onto the faceplate frame. To install the keypad, the faceplate must first be separated from the frame. To avoid damage during the next step, do not use excessive force when prying the faceplate away from the frame. Using a small flat-tip screwdriver or your fingers, pry the top or bottom of the faceplate away from the frame until the retaining tabs disengage. Tilt the faceplate outward and the tabs on the opposite edge will release. At the electrical box, connect the GREEN ground wire of the keypad to the ground wire of the electrical box. (If the electrical box is metal and does not have a ground wire, attach the keypad ground wire to the electrical box. ) Connect the Cresnet connector to the rear of the keypad system adapter. Make sure the two square buttons of the keypad are oriented as desired and position the keypad into the electrical box. 3. 4. 5. CAUTION: Excess wire that is pinched between the keypad and electrical box could short-out. Make sure that all excess wire is completely inside the electrical box and not between the box and the keypad. Using the Phillips tip screwdriver and the supplied Phillips screws, mount the keypad to the electrical box. Make sure that the two square holes of the faceplate are aligned with the square buttons. Holding the faceplate at a slight angle, position the top or bottom of the faceplate onto the faceplate frame. Apply pressure to the opposite edge of the faceplate until the retaining tabs engage onto the frame. Turn Cresnet system power ON. 8. Operations & Installation Guide - DOC. 8150 Lutron® Keypad: CNWM-LU12 · 5 Lutron® Keypad Identity Code Crestron CNWM-LU12 Every equipment and user interface within the Cresnet network requires a unique identity code (NET ID). These codes are recognized by a two-digit hexadecimal number from 03 to FE. The NET ID of the keypad must match an ID code specified in the SIMPL Windows program. The NET ID of the CNWM-LU12 is factory set to 4E. The NET IDs of multiple keypads must all be unique and changed from a PC via VisionToolsTM Pro (VT Pro) or SIMPL Windows. NOTE: VT Pro is a Windows compatible software package for creating Crestron touchpanel screen designs. [. . . ] 8150 Lutron® Keypad: CNWM-LU12 · 9 Lutron® Keypad Crestron CNWM-LU12 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. [. . . ]