User manual CRESTRON CNX-6PAK

[. . . ] This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Crestron CNX-AUDIO-6PAK Six-Zone Audio Package Contents Six-Zone Audio Package: CNX-AUDIO-6PAK 1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Hardware Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Identity Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Select an available source from the Source: field and assign a label for the button on the keypad. Select another room and repeat the process. NOTE: The keypad has standard source selector switch caps installed and a kit of custom switch caps is also supplied with the CNX-AUDIO-6PAK. Instructions for installing the custom switch caps or re-arranging the standard switch caps is provided in the latest revision of the CN-WP12F and CN-WP12N Operations Guide (Doc. NOTE: The lower six buttons on the keypad are fixed. NOTE: The Net ID of each user interface is room specific and shown beneath the user interface on the screen. Add Rooms 12 · Six-Zone Audio Package: CNX-AUDIO-6PAK Operations & Installation Guide - DOC. 8169 Crestron CNX-AUDIO-6PAK Six-Zone Audio Package The switch caps on the lower six buttons on the keypad are fixed and cannot be altered. These include the On/Off button, Volume Up and Down, and Mute. The left and right arrow buttons are for the standard Next and Prev commands, as assigned in the Audio tab of the "Device # Properties" window, as described in "Step 2: Add Sources" on page 9. Step 4: Upload the System The Finish screen provides the final steps to building the logic for the system. This involves creating and compiling the SIMPL Windows program and uploading it to the control system. The completed SIMPL Windows program is saved in . smw format in the system's Program folder and contains all the logic that enables communication between the control system, button panels, controlled devices and other CNX-AUDIO-6PAK hardware. Finish Screen Before uploading the system, it is probably a good idea to verify the communication preferences. The PC running the Wizard should be connected to the front COMPUTER port of the CNMSX-AV via a straight through 9-pin cable. Only then can all system programs be uploaded. Select the Communication Settings button to open the "Port Settings" window, as shown below. Notice that TCP/IP connection is an option. However, a CNXENET+ card (not part of the CNX-AUDIO-6PAK) is required for Ethernet connections. Operations & Installation Guide - DOC. 8169 Six-Zone Audio Package: CNX-AUDIO-6PAK · 13 Verify Port Settings The Documentation button on the final screen of the Wizard displays an HTML report of the entire system including devices and their respective locations. These reports are a great troubleshooting tool. The Edit in Crestron Application Builder button is available for those users that surpass the basic intent of the CNX-AUDIO-6PAK. The options are numerous, but possibilities include: · · · · · Add more zones Add a numeric keypad Add a CT/LC-1000 touchpanel as a user interface Add a wireless touchpanel as a user interface Add a CNXTA to the CNMSX-AV for intercom use. If the Application Builder is to be used, check the Edit in Crestron Application Builder button and click Finish, then modify the system as desired. However, note that once the system is saved in the Application Builder, the Audio Six-Pack Wizard can no longer be used to open the file. When communication between the PC and the control system has been established, click the Upload System button from the final screen of the Wizard. [. . . ] Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. In the event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser. 2. 3. CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. [. . . ]