User manual CRESTRON CNXIO-16

[. . . ] Common ground pins are labeled with a C. Two supplied 9-position connectors can be wired and attached to connectors A and/or B. Operations Guide - DOC. 8125 CNX Analog/Digital Input/Output Expansion Card: CNXIO-16 · 1 CRESTRON Leading Specifications The table below provides a summary of leading specifications for the CNXIO-16. Dimensions and weight are approximations rounded to the nearest hundredth unit. Leading Specifications of the CNXIO-16 SPECIFICATIONS Connectors Power Requirements Ratings: Digital Output Digital Input Input Impedance Input Logic Threshold Analog Input SIMPLTM Windows® CNX Operating System CNX Monitor Dimensions: Height Width DETAILS (2) 9-pin terminal block 24VDC, network power; 2 Watts 250mA sync from maximum 24VDC 0-24VDC 20K Ohm 1. 25VDC 0-10VDC, protected to 24VDC maximum Version 1. 20. 04 or later Version 5. 01. 21X or later Version 2. 05X or later 0. 98 in (2. 49 cm) 5. 00 in (12. 70 cm) As of the date of manufacture, the unit has been tested and found to comply with specifications for CE marking. Installation Items required to install the CNXIO-16 are already attached to the unit. [. . . ] Assume that the touchpanel is used to control the state of lights1 and lights2 in a typical application. Input/outputs on the CNXIO-16 (inA1, outA1 through inA8, outA8) in SIMPL Windows correspond to the CNXIO-16 physical pins A1 through A8. Similarly, inB1, outB1 through inB8, outB8 corresponds to pins B1 through B8. Block Diagram of CNXIO-16 Operations Guide - DOC. 8125 CNX Analog/Digital Input/Output Expansion Card: CNXIO-16 · 3 CRESTRON How to Create the Program Configuration Manager Use the Configuration Manager workspace in SIMPL Windows to select and configure all the devices that need to be included into the system. For this example, add a CNXIO-16 to slot #1 of the control system, shown below. NOTE: SIMPL Windows v1. 20. 04 or later is required to program the CNMSXPRO with a CNXIO-16 card. If using an earlier version of SIMPL Windows, Crestron recommends a SIMPL Windows and operating system upgrade. The latest version can be obtained from the Software Downloads page of Crestron's website (www. crestron. com). New users are required to register in order to obtain access to the FTP site. Graphical System View of CNXIO-16 in SIMPL Windows' Configuration Manager Programming Manager Use the Programming Manager workspace in SIMPL Windows to select symbols and assign their respective signals. For this example, a touchpanel and CNXIO-16 symbols were added automatically when the devices were added to the system in the Configuration Manager workspace. Expand the Network Module folder and double click on the touchpanel for a detail view (alternatively CTRL+D or drag and drop into Detail View). Assign the signals as shown on the next page. 4 · CNX Analog/Digital Input/Output Expansion Card: CNXIO-16 Operations Guide - DOC. 8125 CRESTRON Graphical Detail View of Touchpanel in SIMPL Windows' Programming Manager Expand the Central Control Modules folder. Double click on Port 1 to display the CNXIO-16 in Detail View (alternatively CTRL+D or drag and drop into Detail View). Assign the signals as shown below. Graphical Detail View of CNXIO-16 in SIMPL Windows' Programming Manager NOTE: Each port on the CNXIO-16 can be assigned as either an input or output, but not both. For example, although the software permits the user to assign two independent signals to i1 and o1, it is improper. Expand the Logic folder to display the logic symbols used in this program. They include Analog Compare, Analog Initialize, Multiple One Shots, and OR symbols. View the symbol in detail view (alternatively CTRL+D or drag and drop into Detail View). Some logic symbols are shown in optional sub system folders. Assign the signals as shown below. Graphical Detail View of Analog Compare Symbols in SIMPL Windows' Programming Manager Operations Guide - DOC. 8125 CNX Analog/Digital Input/Output Expansion Card: CNXIO-16 · 5 CRESTRON Graphical Detail View of Analog Compare Symbols in SIMPL Windows' Programming Manager (Continued) Graphical Detail View of Analog Initialize in SIMPL Windows' Programming Manager Graphical Detail View of Multiple One Shots symbol in SIMPL Windows' Programming Manager Graphical Detail View of Multiple OR symbols in SIMPL Windows' Programming Manager 6 · CNX Analog/Digital Input/Output Expansion Card: CNXIO-16 Operations Guide - DOC. [. . . ] Disk drives and any other moving or rotating mechanical parts are covered for a period of one (1) year. CRESTRON warrants all its other products for a period of one year from the defects mentioned above, excluding touchscreen display components which are covered for 90 days. Incandescent lamps are completely excluded from Crestron's Limited Warranty. CRESTRON shall, at its option, repair or replace any product found defective without charge for parts or labor. [. . . ]