User manual CRESTRON CNXMIDI

[. . . ] Use the Phillips tip screwdriver and remove two screws and blank faceplate from the control system. Align the CNXMIDI with the card guides in the open slot and slide the expansion card into position. Firmly press both ends of the CNXMIDI faceplate to seat the expansion card into the control system connector. Tighten the thumb screws to secure the CNXMIDI to the control system. [. . . ] The sequence is triggered when a certain note is received from the keyboard, and stopped at the end of the sequence. Block Diagram of CNXMIDI 4 · CNX MIDI Interface Expansion Card: CNXMIDI Operations Guide - DOC. 8128 CRESTRON How to Create the Program Configuration Manager Use the Configuration Manager workspace in SIMPL Windows to select and configure all the devices that need to be included into the system. For this example, add a CNXMIDI to slot #1 of the control system, shown below. NOTE: SIMPL Windows v1. 21. 03 or later is required to program the CNMSX-AV or PRO with a CNXMIDI card. If using an earlier version of SIMPL Windows, Crestron recommends a SIMPL Windows and operation system upgrade. The latest version can be obtained from the Software Downloads page of Crestron's website (www. crestron. com). New users are required to register in order to obtain access to the FTP site. Graphical System View of CNXMIDI in SIMPL Windows' Configuration Manager Programming Manager Use the Programming Manager workspace in SIMPL Windows to select symbols and assign their respective signals. Expand the Network Module folder and expand the CNXMIDI. Double click on the ST-LT/MIDI serial driver to view it in detail view (alternatively CTRL+D), as shown on the next page. Operations Guide - DOC. 8128 CNX MIDI Interface Expansion Card: CNXMIDI · 5 CRESTRON Graphical Detail View of ST-LT/MIDI in SIMPL Windows' Programming Manager Expand the Logic folder to display the logic symbols used in this program. They include Oscillator, Set Reset Latch, and Ring Counter symbols. Some logic symbols are shown in optional sub system folders. Assign the signals as shown. Graphical Detail View of Oscillator in SIMPL Windows' Programming Manager Graphical Detail View of Ring Counter in SIMPL Windows' Programming Manager Graphical Detail View of Set/Reset Latch in SIMPL Windows' Programming Manager 6 · CNX MIDI Interface Expansion Card: CNXMIDI Operations Guide - DOC. 8128 CRESTRON Problem Solving Troubleshooting The table below provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron technical support representative. CNXMIDI Troubleshooting TROUBLE CNXMIDI does not function. POSSIBLE CAUSE(S) CORRECTIVE ACTION CNX Control System is Verify power to CNX Control System. Circuit card is not Verify CNXMIDI is properly inserted into properly seated in slot. CNX Control System slot per procedures in this Operations Guide. Connect only the required pins controlled equipment is for each communication type. Controlled device is not Use manufacturer-supplied diagnostic tool accepting commands. to verify that controlled device is operating properly. Further Inquiries If after reviewing this Operations Guide for the CNXMIDI, you cannot locate specific information or have questions, please take advantage of Crestron's award winning technical support team by calling: · · · · · · In the US and Canada, call Crestron's corporate headquarters at 1-888-CRESTRON [1-888-273-7876] or 1-201-767-3400. In Europe, call Crestron International at +32-15-50-99-50. In Asia, call Crestron Asia at +852-2341-2016. [. . . ] CRESTRON shall not be liable to honor warranty terms if the product has been used in any application other than that for which it was intended, or if it has been subjected to misuse, accidental damage, modification, or improper installation procedures. Furthermore, this warranty does not cover any product that has had the serial number altered, defaced, or removed. This warranty shall be the sole and exclusive remedy to the purchaser. In no event shall CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages inclusive) arising from the sale or use of this equipment. [. . . ]