User manual CRESTRON SER-1000

[. . . ] Crestron Series 1000 Wall-Mounted Touchpanel Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2002 Crestron Electronics, Inc. Crestron CT-1000 & LC-1000 Touchpanels Contents Series 1000 Wall-Mounted Touchpanels 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Model Differences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Additional touchpanels are assigned different NET ID numbers as they are added. C2Net Device, Slot 9 16 · Series 1000 Wall-Mounted Touchpanels Operations Guide ­ DOC. 5813B Crestron CT-1000 & LC-1000 Setting the Net ID in Device Settings Touchpanels Double-click the LC-1000 icon to open the "Device Settings" window. This window displays the LC-1000 device information. Select the Net ID tab to change the touchpanel Net ID, as shown in the following figure. "Device Settings" Window for the LC-1000 NOTE: SIMPL Windows automatically changes NET ID values of a device added to a program if a duplicate device or a device with the same default NET ID already exists in the program. Always ensure that the hardware and software settings of the NET ID match. For NET ID hardware setting details, refer to "Identity Code" on page 6. LC-1000 Symbol in Programming Manager Programming Manager is where programmers "program" a Creston control system by assigning signals to symbols. The following diagram shows the LC-1000 symbol in the SIMPL Windows' Programming Manager. NOTE: With respect to programming in SIMPL Windows, the CT-1000 symbol is identical, except for the nomenclature. Detail View of the LC-1000 in SIMPL Windows' Programming Manager NOTE: Pin numbers are expandable to 999 Digital, 255 Analog, and 127 Serial. Operations Guide ­ DOC. 5813B Series 1000 Wall-Mounted Touchpanels · 17 Touchpanels Signal Types Crestron CT-1000 & LC-1000 Signals interconnect the various devices and logic symbols that comprise a SIMPL program. Signals can be one of three types: digital, analog, or serial. For any given signal, the signal type is determined by its driving source. That is, if the symbol that drives the signal has an analog output, then, by definition, the connecting signal is analog. In SIMPL Windows, the signal types are color-coded as follows: Digital = Blue Analog = Red Serial = Black Undefined/Other = Green NOTE: "Other" signals are a combination of the three basic types (e. g. many symbols accept either analog or serial signals where the combination is shown as a green signal). The signal type is displayed on the Status Bar when the signal is highlighted. For additional information, refer to Doc. 6120, Crestron SIMPL Windows Symbol Guide. It may be downloaded from the Downloads | Product Manuals | Software section of the Crestron website (www. crestron. com). Digital Signals A digital signal contains one bit of information and usually takes on one of two values: 1 or 0. These two digits can represent the logical values true and false, and they can be represented in an electronic device by the states on/off or high/low, recognized as two voltage levels. (Other common descriptors are active/inactive. ) Analog Signals Unlike digital signals, analog signals can vary continuously in value, in the same manner as a parameter such as volume, temperature, or pressure. Analog signals contain 16 bits of information, which means that this type of signal can have values ranging from 0 to 65535 (216-1). This 16-bit property makes analog signals useful for controlling devices that do not have discrete settings, such as volume controllers, pan/tilt head controllers, and lighting dimmers. Serial Signals Serial signals are much like analog signals, in that they, too, contain 16 bits of information. [. . . ] Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. [. . . ]