User manual CRESTRON ST-CP

[. . . ] Crestron ST-CP SmarTouchTM Control Processor Contents SmarTouchTM Control Processor: ST-CP 1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Physical Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Leading Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Attach the 3. 5 mm stereo connector of the touchpanel to control processor cable (15710, supplied with ST-PK) to the touchpanel. Attach the RJ11 connector of the touchpanel to control processor cable to the ST-CP port, labeled NET. Attach the 500 mA power pack to ST-CP (1000 mA power pack for ST-CP/UK) and insert plug into outlet. The touchpanel should either receive power from the supplied power pack or an internal battery. In the event that the two cables and adapter required to download a program from the control processor to the touchpanel are lost or not acquired via the purchase of the ST-PK, the following two diagrams are provided so that the cables can be made on site. PC to Control Processor Cable 6 · SmarTouchTM Control Processor: ST-CP Operations Guide - DOC. 5820 Crestron ST-CP SmarTouchTM Control Processor Touchpanel to Control Processor Cable Operation When operating the ST-CP under normal conditions, refer to figure shown below for a typical connection diagram. Complete the following steps in the order provided to ensure proper connection of the system. It is assumed that the SmarTouch STS is currently connected for programming. Typical Connection Diagram During Normal Operation ATTACH ANTENNA VCR STIRP POWER PACK (500 mA Supply) (1000 mA for SmarTouch STSI) SENSOR 1. 2. Completely disconnect touchpanel to control processor cable (15710). Completely disconnect PC to control processor cable (15717) and RJ11 to DB9F adapter (15556). Operations Guide - DOC. 5820 SmarTouchTM Control Processor: ST-CP · 7 SmarTouchTM Control Processor 3. 4. Crestron ST-CP Attach supplied antenna to BNC connector labeled RF on the back of the ST-CP. Insert the mono mini plug of the STIRP into one of the four IR OUT ports of the ST-CP. Identifying the correct IR OUT port depends on the designations made when programming. In the illustration provided, it is assumed that the VCR is assigned to PORT A. Refer to the latest revision of the STIRP Installation Instructions (Doc. 5674) for details to attach the STIRP to IR sensor windows. Repeat previous step, as necessary. 5. Problem Solving Troubleshooting The table below provides corrective action for possible trouble situations. Mount the antenna away from the equipment with a BNC male to BNC female 50 ohm cable. Further Inquiries If after reviewing this Operations Guide for the ST-CP, you cannot locate specific information or have questions, please take advantage of Crestron's award winning customer service team by calling: · · · · · In the US and Canada, call Crestron's corporate headquarters at 1-888-CRESTRON [1-888-273-7876] or 1-201-767-3400. In Europe, call Crestron International at +32-15-50-99-50. In Asia, call Crestron Asia at +852-2341-2016. In Latin America, call Crestron Latin America at +5255-5093-2160. In Australia, call Crestron Pacific at +613-9480-2999. For local support from exclusive Crestron factory-trained personnel in New Zealand call Amber Technologies at +649-410-8382. Operations Guide - DOC. [. . . ] Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. [. . . ]