User manual CRESTRON ST-DS

[. . . ] 6 Further Inquiries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Future Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Return and Warranty Policies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Merchandise Returns / Repair Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] There are three possible methods of charging the ST-BTP with the ST-DS. All methods are considered fast charging and take between two and three hours for a fully discharged ST-BTP. Using the touchpanel during charging may take up to three hours and is only permissible with certain Crestron wireless touchpanel models. Method 1: ST-BTP Alone NOTE: Use the optional charging guide when charging the ST-BTP alone (while it is not installed in the touchpanel). Position the charging guide into the ST-DS cavity. Position the ST-BTP, by itself, into the ST-DS cavity to automatically initiate charging. Be sure that the contacts of the ST-DS and ST-BTP touch. Refer to the illustration on the next page to confirm positioning. The CHG LED illuminates while the ST-BTP is charging. When the ST-BTP is fully charged, the CHG LED extinguishes and the RDY LED illuminates. 4 · Docking Station/Charger: ST-DS Operations Guide - DOC. 5738A Crestron ST-DS Charging the ST-BTP (Alone) Docking Station/Charger CONTACTS ST-BTP RECHARGABLE POWER PACK ST-DS SHOWN WITH OPTIONAL CHARGING GUIDE Method 2: ST-BTP Installed in an Inactive Touchpanel NOTE: Do not use the optional charging guide when charging the ST-BTP while installed in the touchpanel. NOTE: This method only applies to certain Crestron wireless touchpanels. In this method, the ST-BTP is properly installed into the touchpanel. Position the touchpanel into the ST-DS cavity, as shown on the next page. Be sure that the contacts of the ST-DS and ST-BTP touch. The CHG LED illuminates while the ST-BTP is charging. When the ST-BTP is fully charged, the CHG LED extinguishes and the RDY LED illuminates. As long as the touchpanel remains inactive (OFF), a fully discharged ST-BTP fully charges in two hours. TouchPanel Properly Positioned (ST-1550C shown) TOP VIEW SIDE VIEW Operations Guide - DOC. 5738A Docking Station/Charger: ST-DS · 5 Docking Station/Charger Crestron ST-DS Method 3: ST-BTP Installed in an Active Touchpanel This method is identical to method 2, except that the touchpanel is active (ON) while charging. As a result, the time to fully charge a discharged ST-BTP can take up to three hours. Fully Discharging the ST-BTP Due to the memory effect of nickel-cadmium (NiCad) cells, Crestron recommends that the ST-BTP be fully discharged for every 25 charge/discharge cycles. The ST-BTP can be fully discharged while in the touchpanel. A button to fully discharge the touchpanel should be available within a designated screen design. This button has a special software identity (reserve join number) and can be recreated and programmed onto any page in the touchpanel project. [. . . ] If the ST-BTP is continually recharged before being fully discharged, the unit learns not to maintain a full charge. This can be avoided by fully discharging the ST-BTP every 25 charging cycles. ST-BTP The ST-BTP is a rechargeable power pack included with each Crestron wireless touchpanel that require one. ST-DS The ST-DS is a docking station and charger, which allows fast charging and trickle charging of the ST-BTP. ST-DS Optional Charging Guide The ST-DS optional charging guide is a template that properly positions a ST-BTP inside the ST-DS cavity. The guide must be used when charging a ST-BTP alone (outside the touchpanel). Operations Guide - DOC. 5738A Glossary of Terms · 9 Docking Station/Charger Crestron ST-DS This page intentionally left blank. 10 · Glossary of Terms Operations Guide - DOC. [. . . ]