User manual CRESTRON TMK-12L WMKT-12L

[. . . ] Post-construction refers to framed walls with drywall hung. This accessory is designed with a mounting plate so that it can be placed anywhere on a wall without the support from a stud. The mounting plate is also ideal for installing the touchpanel in a lectern. NOTE: If necessary, consult the latest revision of the TPS-12L/15L/17L Operations Guide (Doc. [. . . ] Make a small hole near the middle of the designated site; verify that the location is suitable. NOTE: Make the cutout as level and smooth as possible. The mounting plate allows for only minor leveling adjustments. If a larger cutout is accidentally made, consider purchasing the Crestron Mud Mount Kit, MMK-12L. It and the mounting plate supplied with the WMKT-12L provide a cost-effective means of correction. Essentially, The combination of these two kits makes up the Crestron Mud Mount Kit for the Wall, WMKM-12L. Simply follow the "WMKM-12L Procedure" in the latest revision of the Mud Mount Kits Installation Guide (Doc. Use the drywall saw or equivalent to produce a level, rectangular cutout in the drywall (refer to the Drywall Cutout dimensions on page 2 for cutout dimensions). Insert the symmetrical trim ring into the opening, as shown in the following diagram. Insert the Trim Ring into the Opening 4. 5. Carefully pass the mounting plate through the opening and rest it against the interior surface of the drywall. Installation Guide ­ DOC. 6360 Trim Ring Mount Kits: TMK-12L & WMKT-12L · 5 Trim Ring Mount Kits 6. Crestron TMK-12L & WMKT-12L When the mounting plate is in position, bend the top two flanges of the trim ring upward (approximately 90 degrees) and the bottom two flanges downward (approximately 90 degrees). Refer to the following diagram. Bend Flanges ­ Front and Back View NOTE: The mounting plate will have slight play; this is normal. It allows for minor adjustments to the TPS-12L during installation. Run the necessary cables for the touchpanel and secure them behind the drywall. The TPS-12L can be installed using the four tapped holes in the mounting plate. Refer to the latest revision of the TPS-12L/15L/17L Operations Guide (Doc. 6355) or TPS-12G/15G-L Operations Guide (Doc. 6356) for details. CAUTION: Allow an air gap of at least 12 inches in the wall cavity above the touchpanel for heat dissipation. 6 · Trim Ring Mount Kits: TMK-12L & WMKT-12L Installation Guide ­ DOC. 6360 Crestron TMK-12L & WMKT-12L Trim Ring Mount Kits Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. For assistance in your local time zone, refer to the Crestron website (www. crestron. com) for a listing of Crestron worldwide offices. You can also log onto the online help section of the Crestron website to ask questions about Crestron products. First-time users will need to establish a user account to fully benefit from all available features. As of the date of manufacture, the TMK-12L and WMKT-12L have been tested and found to comply with specifications for CE marking. Future Updates As Crestron improves functions, adds new features, and extends the capabilities of the TMK-12L or WMKT-12L, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. [. . . ] Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. This warranty statement supercedes all previous warranties. Trademark Information All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered trademark of Microsoft Corporation. [. . . ]