User manual CRESTRON TPS-IMC-BV

[. . . ] This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Crestron TPS-IMC-BV Interface Module Contents Interface Module: TPS-IMC-BV 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Consult the latest revision of the TPS-XVGA-BV Operations & Installation Guide (Doc. A Triamese cable (15884) is supplied with the TPS-XVGA-BV. Description of the pinouts is shown in the table after this paragraph. Operations Guide - DOC. 5921 Interface Module: TPS-IMC-BV · 3 Interface Module RGB to the Panel Pinouts (RJ45 Port) PIN # 1 2 3 4 5 6 7 8 9 10 Crestron TPS-IMC-BV DESIGNATION VHRR+ GG+ BB+ H+ V+ DESCRIPTION Vertical Sync (Negative) Horizontal or Composite (Negative) Red Video (Negative) Red Video (Positive) Green Video (Negative) Green Video (Positive) Blue Video (Negative) Blue Video (Positive) Horizontal or Composite (Positive) Vertical Sync (Positive) · AUDIO ­ This 8-position RJ45 mates with the TPS-5000 or TPS-6000 touchpanel. A Triamese cable (15884) is supplied with the TPS-XVGA-BV. This port provides audio input to the touchpanel and mic out from the touchpanel to audio amplifiers. Description of the pinouts is shown in the table after this paragraph. AUDIO Pinouts PIN # 1 2 3 4 5 6 7 8 DESCRIPTION Audio Shield Audio Left + Audio Left Audio Right + Audio Right Mic Out Shield Mic Out + Mic Out - · AUDIO INPUT ­ This port is designed for future use. This 8-pin RJ45 port mates with an audio switcher, if available. Description of the pinouts is shown in the table after this paragraph. AUDIO INPUT Pinouts (RJ45 Port) PIN # 1 2 3 4 5 6 7 8 DESCRIPTION Mic + Mic Mic + Audio Left + Audio Left Mic Audio Right + Audio Right - · AUDIO INPUT ­ The port mates with a six-pin connector, supplied, and provides differential/single ended audio input and output. Description of the pinouts is shown in the table after this paragraph. 4 · Interface Module: TPS-IMC-BV Operations Guide - DOC. 5921 Crestron TPS-IMC-BV AUDIO INPUT Pinouts (6-Pin Port) PIN S R+ RL+ LS Interface Module DESCRIPTION Shield Right Positive Right Negative Left Positive Left Negative Shield · MIC OUT ­ The port mates with a three-pin connector, supplied, and produces line level differential output. Description of the pinouts is shown in the table after this paragraph. MICROPHONE Pinouts PIN M+ MS DESCRIPTION Positive Negative Shield BAL/COAX Video Switch A single two-position toggle switch is centrally located on the top panel of the TPS-IMC-BV. Use the switch to select between balanced video (BAL) and unbalanced video (COAX). Leading Specifications The table after this paragraph provides a summary of leading specifications for the TPS-IMC-BV. Dimensions and weight are rounded to the nearest hundredth unit. Leading Specifications for the TPS-IMC-BV SPECIFICATION Dimensions DETAILS Height: 3. 20 in (8. 13 cm) Width: 7. 70 in (19. 56 cm) Depth: 1. 25 in (3. 18 cm) Weight 1. 15 lb (0. 52 kg) As of the date of manufacture, the TPS-IMC-BV has been tested and found to comply with specifications for CE marking. Setup Network Wiring NOTE: When making wire connections, refer to the latest revision of the Cresnet Network Interconnect Drawing (Doc. The document can be obtained from the Downloads page (CABLES and MANUAL Libraries) of the Crestron website (www. Search for the CRESNET. PDF files. Interface Module: TPS-IMC-BV · 5 Operations Guide - DOC. 5921 Interface Module Crestron TPS-IMC-BV When calculating the wire gauge for a particular network run, the length of the run and the power factor of each network unit to be connected must be taken into consideration. If network units are to be daisy-chained on the run, the power factor of each network unit to be daisy-chained must be added together to determine the power factor of the entire chain. The length of the run in feet and the power factor of the run should be used in the following resistance equation to calculate the value on the right side of the equation. Resistance Equation R < 40, 000 L x PF Where: R = Resistance (refer to table below). PF = Power factor of entire run (or chain). The required wire gauge should be chosen such that the resistance value is less than the value calculated in the resistance equation. [. . . ] Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. [. . . ]