User manual CRESTRON TPS-VIDL

[. . . ] 5830 Video Card for TPS/Lectern Panel: TPS-VIDL · 1 Video Card for TPS/Lectern Panel TPS-VIDL Top View Crestron TPS-VIDL 2. 63 in (6. 67 cm) 5. 00 in (12. 70 cm) Leading Specifications The table below provides a summary of leading specifications for the TPS-VIDL. Dimensions and weight are rounded to the nearest hundredth unit. Leading Specifications of the TPS-VIDL SPECIFICATION Power Requirements Video Types Video Formats Video Format Detection SIMPLTM Windows® DETAILS 24VDC Cresnet power, load factor of 8 Watts. NTSC or PAL Composite or S-Video Within 4-seconds. Version 1. 40. 07 or later 1 with the addition of smwlib89. exe and smwlib89. txt. [. . . ] 5830 Crestron TPS-VIDL Video Card for TPS/Lectern Panel 4. Using a #1 Phillips screwdriver, loosen and remove the two screws that secure the PCB blank plate and remove the plate. Remove PCB Blank Plate 5. As shown below, align the pins on the touchpanel interface connector of the TPS-VIDL with the touchpanel motherboard connector. Install TPS-VIDL 6. Press TPS-VIDL until pins are fully seated. Make sure that the mounted screws align with mounting posts of the motherboard. Tighten the card mounting screws to finger-tight. Operations & Installation Guide - DOC. 5830 Video Card for TPS/Lectern Panel: TPS-VIDL · 5 Video Card for TPS/Lectern Panel Crestron TPS-VIDL CAUTION: The TPS-VIDL connectors may have to be aligned slightly to fit through the openings in the rear cover. Align the connectors of this card (or any other optional card that is installed) carefully to prevent damage to the card, cover, or touchpanel. As shown below, install the touchpanel rear cover by sliding it over the TPS-VIDL connectors. Install Touchpanel Rear Cover 9. Using a #1 Phillips 1/4-inch hex bit and an inchpound torque driver, install 10 screws and tighten to 4-inch pounds (0. 45 Newton-meters) to secure cover. Install Touchpanel Rear Cover Screws 6 · Video Card for TPS/Lectern Panel: TPS-VIDL Operations & Installation Guide - DOC. 5830 Crestron TPS-VIDL Video Card for TPS/Lectern Panel NOTE: Depending upon the individual installation, video connectors #1 or #2 may be used. The input signals are identical, only the connector type is different. Refer to the diagram below and make the appropriate S-video or composite video connection(s) as shown. Attach Appropriate Video Cables VIDEO CONNECTORS #1 VIDEO CONNECTORS #2 { C COMP Y FROM S-VIDEO LUMINANCE OR COMPOSITE VIDEO OUTPUT C Y + -S+ -S FROM S-VIDEO CHROMINANCE OUTPUT NOTE: Refer to the latest revision of the TPS-5000L, TPS-6000L, or TPS-TPI Operations & Installation Guide (Doc. 5825, 5783, or 5855, respectively) or, if applicable, BB-5000 or BB-6000 Installation Guide (Doc. 5826 or 5827, respectively) for the proper installation procedure of the touchpanel. The latest software version of the Operations & Installation Guides can be obtained from the Downloads page (MANUAL Library) of Crestron's website (www. crestron. com). NOTE: Refer to the latest revision of the TPS-5000L, TPS-6000L, or TPS-TPI Operations & Installation Guide (Doc. 5825, 5783, or 5855, respectively) to configure the touchpanel for video input. Operations & Installation Guide - DOC. 5830 { FROM S-VIDEO LUMINANCE OR COMPOSITE VIDEO OUTPUT NTSC/PAL INPUT FROM S-VIDEO CHROMINANCE OUTPUT Video Card for TPS/Lectern Panel: TPS-VIDL · 7 Video Card for TPS/Lectern Panel Crestron TPS-VIDL Problem Solving Troubleshooting The table below provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron technical support representative. TPS-VIDL Troubleshooting TROUBLE Video window of touchpanel has no display. POSSIBLE CAUSE(S) Improper video connection(s). Incorrect video format selected. CORRECTIVE ACTION Verify proper connections at NTSC/PAL INPUT ports. Select proper video format or autodetect in touchpanel configuration setup menu. [. . . ] Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. In the event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser. 2. 3. CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. [. . . ]