User manual CRESTRON TPSBLOCK-10

[. . . ] 5979A 10-Position RJ45 Panel Mount Interface: TPSBLOCK-10 · 1 10-Position RJ45 Panel Mount Interface Crestron TPSBLOCK-10 interface module). Refer to the table below for touchpanel and interface modules that are used with the TPSBLOCK-10. TPSBLOCK-10 Interface Applications INTERFACE MODULE MODULE TPSBLOCK-10 ISYSTM TOUCHPANEL MODULE AVAILABILITY DOC. # INTERFACE TPS-4500 Supplied w/touchpanel TPS-4500IMW Sold Separately Supplied TPS-IMC w/touchpanel TPS-4500IMC TPS-IMC-BV Sold Separately * TPS-IMW Sold Separately 5890 5913 5856 5921 5857 NET/VIDEO only NET/VIDEO only NET/VIDEO only NET/VIDEO or RGB NET/VIDEO only TPS-5000 & TPS-6000 * The TPS-IMC-BV is supplied with the optional TPS-XVGA-BV card that can only be installed into specific touchpanels. [. . . ] NOTE: If affixing a NET/VIDEO or RGB label near the TPSBLOCK10 (above or below is recommended), a 0. 200 in (0. 508 cm) by 0. 700 in (1. 778 cm) area is required. NOTE: Extron has made available Architectural Adapter Plates (AAPs) for mounting the TPSBLOCK-10 for Cresnet touchpanel connection. Refer to "Custom Adapter Plates" on page 5 for details. If using AAPs, skip steps 2 and 3 in the subsequent procedure. On the panel or desktop pop-up/tilt-up device, determine an adequate location for the TPSBLOCK-10. Using the proper tools, cut-out and remove the rectangular area from the panel or desktop pop-up/tilt-up device. TPSBLOCK-10 Installation (1 of 3) - Cutout Diagram 0. 675 in (1. 715 cm) 0. 590 in (1. 500 cm) 3. Using an electric drill and 0. 136-inch (#29 or approximately 9/64-inch) drill bit, drill two TPSBLOCK-10 mounting holes. TPSBLOCK-10 Installation (2 of 3) - Mounting Hole Diagram 0. 313 in (0. 795 cm) 0. 143 in (0. 362 cm) 0. 276 in (0. 701 cm) 0. 136 in DIAMETER 4. At the inner surface of the panel or desktop pop-up/tilt-up device, position the female connector of the TPSBLOCK-10 4 · 10-Position RJ45 Panel Mount Interface: TPSBLOCK-10 Installation Guide - DOC. 5979A Crestron TPSBLOCK-10 10-Position RJ45 Panel Mount Interface into the cutout area and align the drilled mounting holes with the TPSBLOCK-10 mounting brackets. At the outer surface of the panel or desktop pop-up/tilt-up device, loosely install two #4-40 screws of adequate length (not supplied) through the surface into the TPSBLOCK-10 mounting brackets. Tighten screws to finger-tight then, using an appropriate screwdriver, tighten to a torque that is adequate for the surface material. TPSBLOCK-10 Installation (3 of 3) - Secure TPSBLOCK-10 6. Connect the male RJ45 plug of the TPSBLOCK-10 cable to the NET/VIDEO or RGB port of the TPS interface module or TPS wall-mounted interface module. If desired, peel the appropriate NET/VIDEO or RGB label (supplied) from the paper backing and affix to the surface of the panel or desktop pop-up/tilt-up device near (above or below is recommended) the TPSBLOCK-10. At the outer surface of the panel or desktop pop-up/tilt-up device, connect the touchpanel NET/VIDEO or RGB cable (supplied with touchpanel) to the female RJ45 connector of the TPSBLOCK-10. Custom Adapter Plates Extron Architectural Adapter Plates (AAPs), shown on the next page, are available for mounting Crestron TPSBLOCK-10 for touchpanel connection. These two-space AAPs allow the mounting of one or two TPSBLOCK-10 interfaces. The AAPs must be ordered separately from Extron; consult the Extron website (www. extron. com) for specifications and ordering details. Installation Guide - DOC. 5979A 10-Position RJ45 Panel Mount Interface: TPSBLOCK-10 · 5 10-Position RJ45 Panel Mount Interface Extron Architectural Adapter Plates (AAPs) Crestron TPSBLOCK-10 Further Inquiries If after reviewing this Installation Guide, you cannot locate specific information or have questions, please take advantage of Crestron's award winning customer service team by calling: · In the US and Canada, call Crestron's corporate headquarters at 1-888-CRESTRON [1-888-273-7876] or 1-201-767-3400. [. . . ] Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. In the event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser. 2. 3. CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in materials and workmanship under normal use for a period of three (3) years from the date of purchase from CRESTRON, with the following exceptions: disk drives and any other moving or rotating mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen display and overlay components are covered for 90 days; batteries and incandescent lamps are not covered. This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON dealer. [. . . ]