User manual CULLIGAN IRON-CLEER PLUS AUTOMATIC WATER FILTER 12 IRON CLEER

[. . . ] Culligan® Iron-Cleer® Plus Automatic Water Filter Owners Guide Thank You And Welcome To Your New World Of Better Living With Culligan Water. This system and its installation must comply with state and local regulations. The System is ONLY to be supplied with cold water. The Culligan® Iron Cleer® water filter has been tested and certified by WQA against WQA S-200 for the effective reduction of iron up to 1, 400 gallons for 10" units and 2, 000 gallons for 12" units. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. [. . . ] This cycle is usually brine draw / slow rinse for softeners and a settling time for filters. The display will show the "BRINE RINSE" and "MINS" icons and the cycle time in the right most digits. Adjust the value with the "Up" or "Down" keys. Pressing the "Program" key will save the setting and move to the next programming step. · Cycle 3 Time (Fast Rinse) ­ This setting is used to set the time in minutes for cycle 3. This cycle is usually fast rinse for softeners and filters. For softener applications it may include the refill operation. The display will show the "FAST RINSE", "/", "REFILL" and "MINS" icons for 4-cycle valves or "FAST RINSE" and "MINS" icons for 5-cycle valves and filters with the cycle time in the right most digits. Adjust the value with the "Up" or "Down" keys. Pressing the "Program" key will save the setting and move to the next programming step. · Regeneration Interval - This setting is used to set the days between regeneration in time clock mode. It is also active in meter mode if the time clock backup DIP switch # 10 is set to on. The display will show "REGEN" icon and "dAYS" as well as the numbers to change. Adjust the value with the "Up" or "Down" keys. Pressing the "Program" key will save the setting and move to the next programming step. 8 · Filter Media Life (Change Media) - This setting is used in Filter Mode ONLY with flow meter attached. It enables or disables an alarm code ("CHANGE MEDIA") that indicates the end of life for the filter media. The display will show "LIFE" in the left most characters and toggle between "Y" and "N" in the right most character with the "+" and "-" keys. If "NO" is selected, the alarm is disabled and the `Total Capacity' setting will be treated as it is in Flow Meter Mode (softener). If "YES" is selected, the alarm is enabled and will sound when the `Total Flow/Life of Unit' statistic = `Total Capacity' setpoint, indicating that it is time to change the filter media. Pressing "Program" key will save and advance to the next step. Programming (cont. ) · Total Capacity Set Point (Max Capacity) - This setting is used to program a value that corresponds to the maximum capacity that can be expected from a unit before it is completely exhausted (no reserve). This setting will only appear if a flow meter is connected to the circuit board. The display will show the "REGEN" icon and "MAXCAP" for two seconds and then display the "REGEN" and "GALLONS" or "LITERS" icons (depending on DIPswitch #7 setting) and the setting numbers to adjust. Adjust the value with the "Up" or "Down" keys. When the capacity used equals this total capacity setting with the "Life" feature off, the control will regenerate either immediately or at the time of regen based on the "hidden programming menu" setting. With the "Life" feature on, the control will use this setting to trigger the "Change Media" alarm. [. . . ] ______ p. m. Regeneration Interval __________ days (Time clock models) Number of people in household Water Analysis Total Hardness _______ (gpg) Total Iron _______ (ppm) Hydrogen Sulfide____________ (ppm) Other 19 Culligan Limited Warranty Culligan® Iron-Cleer® Automatic Water Filters You have just purchased one of the finest water conditioners made. As an expression of our confidence in Culligan International Company products, your water conditioner is warranted to the original end-user, when installed in accordance with Culligan specifications, against defects in material and workmanship from the date of original installation, as follows: For a period of ONE YEAR For a period of FIVE YEARS For a period of TEN YEARS The entire conditioner The AccuSoft® circuit board The control valve body, excluding internal parts The conditioner tank If a part described above is found defective within the specified period, you should notify your independently operated Culligan dealer and arrange a time during normal business hours for the dealer to inspect the water conditioner on your premises. Any part found defective within the terms of this warranty will be repaired or replaced by the dealer. You pay only freight from our factory and local dealer charges. [. . . ]