User manual CYBEX INTERNATIONAL 13170 GLUTE

[. . . ] VR1® Glute Owner's Manual Strength Systems Part Number 13170-999-4 D www. cybexinternational. com VR1® Glute Owner's Manual Strength Systems Part Number 13170-999-4 D Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. VR1® and its mark are registered trademarks of Cybex International, Inc. DISCLAIMER: Cybex International, Inc. , makes no representations or warranties regarding the contents of this manual. We reserve the right to revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such revisions or changes. © Copyright 2010, Cybex International, Inc. [. . . ] Provide the technician with a detailed description of the problem you are having or the defect in the item you wish to return. 13000-353 13000-354 13000-353 4800-557 13000-552 4700-337 4700-338 DESCRIPTION FOOT PAD FOOT PAD FOOT PAD DECAL, WEIGHT PLATE (10-150) DECAL, WEIGHT PLATE (10-220) WEIGHT PLATE (LIGHT) 10 LB WEIGHT PLATE (STANDARD) 15 LB 5 7/32" Allen wrench 3/4" Socket or wrench Hammer 3/16" Pin punch NOTE: Two people will be required to perform this procedure. NOTE: It is the responsibility of the facility owner/owner of the equipment to ensure that there is appropriate clearance around each machine to allow for safe use and passage. Read and understand all instructions thoroughly before assembling this product. 2 4 1 3 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 4. 5 9. 0 13. 5 18. 0 22. 5 27. 0 31. 5 36. 0 40. 5 45. 0 49. 5 54. 0 58. 5 63. 0 67. 5 10 25 40 55 70 85 100 115 130 145 160 175 190 205 220 4. 5 11. 5 18. 0 25. 0 31. 5 38. 5 45. 0 52. 0 58. 5 65. 5 72. 5 79. 0 85. 5 93. 0 100. 0 10lb 6 15lb 7 2. Verify you have received the appropriate configuration. Verify that you received the correct color machine that you ordered. Verify you received the proper weight stack and weight stack decals. Verify you received the appropriate owner's manual. NOTE: If weight stacks need to be removed before moving to desired location proceed to step 7. NOTE: If weight stacks need to be installed proceed to step 8. WARNING: Use extreme caution when removing shipping cones and installing feet. Failure to do so could result in injury. With an assistant, carefully remove each (standard) cone-shaped shipping support using a 3/4" socket or wrench. Carefully place rubber feet (supplied with machine) on each foot of the frame. NOTE: It is important that you perform regular inspection and maintenance activities on your equipment. See the CYBEX VR1 Owner's Manual for inspection and maintenance activities. If you do not have a CYBEX Owner's Manual or if you have any questions or concerns, Call Cybex Customer Relations at 888-462-9239. Assembly Page 4-1 Cybex VR1 13170 Glute Owner's Manual 5. Securely anchor machine to the floor using the anchor holes provided in each machine. NOTE: Cybex is not responsible for the actual anchoring of equipment. NOTE: Use fasteners having a minimum of 500 lbs tensil capacity (3/8" grade 2 bolts or better). NOTE: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim any leg or frame not in contact with surface using flat washers. [. . . ] See Figure 5. Attachment Hole NOTE: Replace bar if less than 1/8" of material remains to the edge. Figure 5 4. Inspect snap links for proper latching (indicates wear) Replace all worn snap links immediately. Replace all loose or worn grips immediately. This includes instructional placards, warning and caution decals. [. . . ]