User manual CYBEX INTERNATIONAL 13200 AB-BACK

[. . . ] VR1® Abdominal/Back Extension Owner's and Service Manual Strength Systems Part Number 13200-999-4 C www. cybexinternational. com VR1® Abdominal/Back Extension Owner's and Service Manual Strength Systems Part Number 13200-999-4 C Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. VR1® and its mark are registered trademarks of Cybex International, Inc. DISCLAIMER: Cybex International, Inc. , makes no representations or warranties regarding the contents of this manual. We reserve the right to revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such revisions or changes. © Copyright 2010, Cybex International, Inc. [. . . ] Failure to do so could result in injury. With an assistant, carefully remove each (standard) cone-shaped shipping support using a 3/4" socket or wrench. Carefully place rubber feet (supplied with machine) on each foot of the frame. NOTE: It is important that you perform regular inspection and maintenance activities on your equipment. See the CYBEX VR1 Owner's Manual for inspection and maintenance activities. If you do not have a CYBEX Owner's Manual or if you have any questions or concerns, Call Cybex Customer Relations at 888-462-9239. Assembly Page 4-1 Cybex VR1 13200 Abdominal/Back Extension Owner's Manual 5. Securely anchor machine to the floor using the anchor holes provided in each machine. NOTE: Cybex is not responsible for the actual anchoring of equipment. NOTE: Use fasteners having a minimum of 500 lbs tensil capacity (3/8" grade 2 bolts or better). NOTE: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim any leg or frame not in contact with surface using flat washers. Using a 7/32" Allen wrench, remove the two Button Head Socket Cap Screws (BHSCS) securing the top cap to the frame. See Figure 1. BHSCS Shroud Top Cap Figure 1 B. Carefully lift shroud up and out of machine. Slide spring loaded guide rod cap down guide rod until cap is clear of frame. NOTE: Guide rod cap contains a compression spring that will fly if grasp is not released slowly. Guide Rod Cap Guide Rod Cap Compression Spring Figure 2 Guide Rods Compression Spring Assembly Page 4-2 Cybex VR1 13200 Abdominal/Back Extension Owner's Manual F. Remove guide rod cap and spring and set aside. Repeat steps 7D - 7F for other guide rod. Using a 3/16" pin punch and hammer, carefully remove roll pin securing cable end to top weight connector. Carefully lean guide rods slightly outward. NOTE: Excessive pressure on guide rods may damage lower guide rod caps. Cable End Top Weight Connector Roll Pin Figure 3 J. Slide top weight up and out of machine and carefully set aside. [. . . ] Humidity - The unit is designed to function normally in an environment with a relative humidity range of 30% to 75%. NOTE: Do not install or use the unit in an area of high humidity, such as in the vicinity of a steam room, sauna, indoor pool or outdoors. Exposure to extensive water vapor, chlorine and/or bromine could adversely affect the electronics as well as other parts of the machine. Temperature - The unit is designed to function normally in an environment with an ambient temperature range of 50 F (10 C) to 104 F(40 C) degrees. o o o o Storage Humidity - The unit can be shipped and stored in an environment with a relative humidity range of 10% to 90%. NOTE: Do not store the unit in an area of high humidity, such as in the vicinity of a steam room, sauna, indoor pool or outdoors. Exposure to extensive water vapor, chlorine and/or bromine could adversely affect the electronics as well as other parts of the machine. Temperature - The unit can be shipped and stored in an environment with an ambient temperature range of 32 F (0 C) and 140 F (60 C) degrees. o o o Maintenance Page 5-7 Cybex VR1 13200 Abdominal/Back Extension Owner's Manual This page intentionally left blank. Maintenance Page 5-8 Cybex VR1 13200 Abdominal/Back Extension Owner's Manual 6 - Service Please refer to the next several pages for parts lists, exploded-view diagrams and cable and belt routing diagrams. NOTE: All inspections and repairs must be performed by trained service personnel only. Cybex will void warranty if non-Cybex replacement parts are used. Service Page 6-1 Cybex VR1 13200 Abdominal/Back Extension Owner's Manual This page intentionally left blank. Service Page 6-2 Cybex VR1 13200 Abdominal/Back Extension Owner's Manual ABDOMINAL/BACK EXTENSION PRODUCT NO. 13200 B A K D F H E L M G L NOTE: See exploded-view diagram for location of I (serial number decal) and J (weight selector pin). [. . . ]