User manual CYBEX INTERNATIONAL 16120 SMITH PRESS

[. . . ] Cybex® Plate Loaded 16120 Smith Press Owner's Manual Strength Systems Part Number 16120-999-4 E www. cybexintl. com Table of Contents Safety Safety . . 9 Exercise Customer Service Contacting Service . 11 Return Material Authorization (RMA) . . 15 Maintenance Daily Procedures . [. . . ] INSET . 06 ocation when doingInspect machine prior to 9. DO NOT use if it MATERIAL: appears damaged or ISE inoperable. THIS NOTE REFERS TO ALL PLASTIC PARTS ble 10. DO NOT attempt to fix AND ASSEMBLIES CONTAINING PLASTICS. n a brokenPMSjammed See Engineering Drawing 4000Y316-X for specifications. or 108 YELLOW RAW MATERIAL AND COMPONENTS ON NOTE: SUB-ASSEMBLIES AND ASSEMBLIES MUST machine. COMPLY WITH EUROPEAN DIRECTIVE RoHS 2002/95/EC. ment of adjustable Report any malfunctions, FINISH: an immediate exit damage or repairs to the dent or emergency. Replace any warning labelsPART NUMBER worn if damaged, or illegible. 6 PT ARIAL ND WITH 5220-364-4 A BOLD SAFETY ORANGE PMS152 BLACK TRIANGLE W/ ORANGE EXCLAMATION POINT, BLACK LETTERS 32 PT ARIAL BOLD pecs Master Artwork D WARNING ecs Master Artwork MATERIAL: CAUTION CAUTION Personal injury may occur. Keep away from moving parts to avoid injury. 4000Y316-4 A Master Artwork TITLE: DWG. BY 16120-340-4 B RNING DATE TECH. APPR. DATE FINISH: CHECKED BY DATE MFG. APPR. DATE SIZE SCALE SHEET DWG. NO. REV. OF C EXCEPT AS NOTED DIMENSIONS IN INCHES GENERAL TOLERANCES: 2 DECIMALS ± . 03 3 DECIMALS ± . 015 ANGLES ± 1° FEATURES SHOWN PERPENDICULAR OR PARALLEL SHALL BE SO WITHIN ± 1° REMOVE ALL BURRS BREAK SHARP EDGES . 005/. 010 R SURFACE FINISH INDICATED PER ANSI B46. 1-1985 REMOVE CARBURIZATION AND SCALE FROM LASER AND PLASMA CUT EDGES GENERAL MACHINING TITLE: DECAL, CAUTION ENG DATE DWG. APPR. BB CHECKED BY DATE MFG. APPR. 125 SIZE B 1:1 1 SHEET OF 1 4000Y316 wing 16120-340-X for material specifications. MATERIAL: DIMENSIONS IN INCHES IAL MUST COMPLY TO UNION DIRECTIVE RoHS (RESTRICTION OUS SUBSTANCES) EXCEPT AS NOTED GENERAL ALL MATERIAL MUST COMPLY TO 2 DECIMALS ± . 03 EUROPEAN UNION DIRECTIVE TOLERANCES: SURFACE FINISH ± . 015 3 DECIMALS 2002/95/EC RoHS (RESTRICTION OF HAZARDOUS SUBSTANCES) ANGLES ± INDICATED PER 1° 2 DECIMALS ± . 03 FEATURES FINISH: ANSI B46. 1-1985SHOWN PERPENDICULAR OR 3 DECIMALS ± . 015 ANGLES ± 1° FEATURES SHOWN PERPENDICULAR OR PARALLEL SHALL BE SO WITHIN ± 1° DIMENSIONS REMOVE ALL BURRS IN INCHES BREAK SHARP EDGES GENERAL . 005/. 010 R TOLERANCES: EXCEPT AS NOTED REMOVE ALL BURRS BREAK SHARP EDGES . 005/. 010 R TITLE: OWATONNA OWATONNA TITLE: SURFACE FINISH INDICATED PER ANSI B46. 1-1985 GENERAL REMOVE PARALLEL SHALL BE CARBURIZATION JKW/BG MACHINING SO WITHIN ± 1° AND SCALE FROM LASER CHECKED BY AND PLASMA CUT EDGES REMOVE CARBURIZATION AND SCALE FROM LASER CHECKED BY AND PLASMA CUT EDGES DATE DWG. BY DECAL, WARNING ENGLISH REL/BG DWG. DATE DATE DECAL, WARNING ENGLISH 3-10-09 DWG. NO. 125 SIZE GENERAL MACHINING 125 BB DATE 1:1 B4/1/091 OF 1 SCALE SHEET TECH. For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239. For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300 or fax 508-533-5183. [. . . ] SHCS (Qty 4) Guide Shaft Bearing Housing Loctite Washers (Qty 4) Weight Bar Bracket 18 Cybex Plate Loaded 16120 Smith Press Owner's Manual 6. Cable Installation. · · · · Locate two Hex Head Cap Screw HHCS from shipping package. Place a small drop of loctite on HHCS and in threaded hole. Using a 7/16" wrench, attach cable end to weight bar bracket with HHCS. [. . . ]