User manual CYBEX INTERNATIONAL BRAVO PRESS

[. . . ] Part Number 18010-999-4 Cybex Bravo Press Owner's Manual Strength Systems www. cybexintl. com Table of Contents Safety Safety Guidelines And Practices . 3 6 7 8 9 Assembly Machine Specifications. . 18 21 23 24 25 Customer Service Product Registration . . 26 26 27 28 28 Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. [. . . ] Remove the four shipping cones using a 3/4" socket or wrench. Attach foot pads to each foot of frame 3. Remove back panels from machine. 18010cannotfit through doorway 4. Remove spiral pin connecting pulley using a hammer and a 3/16" pin punch. Spiral pin 6. Move pulley and cable connection out of the way 7. Guide rod cap contains a compression spring that will fly if grasp is not released slowly. Slide spring loaded guide rod cap down guide rod until cap is clear of frame. Slowly release grasp of guide rod cap and remove. 12 Cybex 18010 Bravo Press Owner's Manual If 8. Remove plastic insert plug, located at top of machine. Loosen the two button head socket cap screws (BHSCS) securing handle bar to frame using a 7/32" Allen wrench. 18010cannotfit through doorway BHSCS Handle Bar 12. Hold threaded block in place with fingers and remove the BHSCS. Do not let threaded block fall down in tube. Threaded block 13 Cybex 18010 Bravo Press Owner's Manual If Then 4. Remove BHSCS and locknuts, remove one side of mounting tube using a 7/32" Allen wrench and a 9/16" wrench. Mounting Tube 18010cannotfit through doorway 5. Reattach frame halves and securely tighten the BHSCS and locknuts. Place two drops of Loctite® 242 to each BHSCS and in thread holes of threaded block for handle bar. Securely tighten BHSCS to threaded block. Securelyanchormachinetothefloor To maximize stability, equipment must be secured to a solid level surface. · Cybex · Use · If is not responsible for the actual anchoring of equipment. tensile capacity (3/8'' grade 2 bolts or better). legs/frame does not contact surface, DO NOT pull down with anchors. Shim any leg or framenotincontactwithsurfaceusingflatwashers. 14 Cybex 18010 Bravo Press Owner's Manual Install individual weight plates one at at time 1. Position each weight plate so wide edges of bushings face upward and narrow edges of bushings face downward. RE COR CT WRO NG Wide bushing edge faces upward 2. [. . . ] All parts can be found on the web at www. cybexintl. com Shipping Address Contact Name Include a description of the problem. In addition to your shipping address and contact name, your account number is helpful but not required. You may also fax orders to 508-533-5183. MATERIAL: DIMENSIONS IN INCHES ALL MATERIAL MUST COMPLY TO EUROPEAN UNION DIRECTIVE 2002/95/EC RoHS (RESTRICTION OF HAZARDOUS SUBSTANCES) FINISH: EXCEPT AS NOTED REMOVE ALL BURRS BREAK SHARP EDGES . 005/. 010 R SURFACE FINISH INDICATED PER ANSI B46. 1-1985 GENERAL TOLERANCES: 2 DECIMALS ± . 03 3 DECIMALS ± . 015 ANGLES ± 1° FEATURES SHOWN PERPENDICULAR OR PARALLEL SHALL BE SO WITHIN ± 1° REMOVE CARBURIZATIO AND SCALE FROM LASE AND PLASMA CUT EDGE GENERAL MACHINING 125 27 Cybex 18010 Bravo Press Owner's Manual Return Material Authorization (RMA) The Return Material Authorization (RMA) system is used when returning material for placement, repair or credit. The system assures that returned materials are properly handled and analyzed. Follow the following procedures carefully. [. . . ]