User manual CYBEX INTERNATIONAL BRAVO PULL

[. . . ] Part Number 18020-999-4 Cybex Bravo Pull Owner's Manual Strength Systems www. cybexintl. com Table of Contents Safety Safety Guidelines And Practices . 3 6 7 8 9 Assembly Machine Specifications. . 19 22 24 25 26 Customer Service Product Registration . . 27 27 28 29 29 Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. [. . . ] Attach foot pads to each foot of frame. 11 Cybex 18020 Bravo Pull Owner's Manual If Then Two people will be required for this procedure 1. Remove the four shipping cones using a 3/4" socket or wrench. Attach foot pads to each foot of frame 3. Remove back panels from machine. 18020cannotfit through doorway 4. Remove spiral pin connecting pulley using a hammer and a 3/16" pin punch. Spiral pin 6. Move pulley and cable connections out of the way. Guide rod cap contains a compression spring that will fly if grasp is not released slowly. Slide spring loaded guide rod cap down guide rod until cap is clear of frame. Slowly release grasp of guide rod cap and remove. 12 Cybex 18020 Bravo Pull Owner's Manual If 8. Remove button head socket cap screw (BHSCS) and locknut to remove cable pulley using a 7/32" Allen wrench and 9/16" wrench. Cable Pulley Cable Pulley BHSCS BHSCS 18020cannotfit through doorway 2. Remove cable pulleys and cable out of the way. Remove BHSCS and locknuts securing one side of top front cross bar and top rear cross tube using a 7/32" Allen wrench and 9/16" wrench. Top Front Cross Tube BHSCS Qty 4 Top Rear Cross Tube BHSCS Qty 4 13 Cybex 18020 Bravo Pull Owner's Manual If Then 2. Remove the button head socket cap screw (BHSCS) securing adjustable post to frame using a 7/32" Allen wrench. Adjustable Post BHSCS 18020cannotfit through doorway 3. Remove BHSCS and locknuts securing mounting tube to frame using a 7/32" Allen wrench and 9/16" wrench. Mounting Tube BHSCS Qty 2 4. Reattach frame halves and securely tighten the BHSCS and locknuts. 14 Cybex 18020 Bravo Pull Owner's Manual Securelyanchormachinetothefloor To maximize stability, equipment must be secured to a solid level surface. · · · Cybex is not responsible for the actual anchoring of equipment. Use fasteners having a minimum of 500 lbs. tensile capacity (3/8'' grade 2 bolts or better). If legs/frame does not contact surface, DO NOT pull down with anchors. Shim any leg or framenotincontactwithsurfaceusingflatwashers. Install individual weight plates one at at time 1. [. . . ] All parts can be found on the web at www. cybexintl. com Shipping Address Contact Name Include a description of the problem. In addition to your shipping address and contact name, your account number is helpful but not required. You may also fax orders to 508-533-5183. MATERIAL: DIMENSIONS IN INCHES ALL MATERIAL MUST COMPLY TO EUROPEAN UNION DIRECTIVE 2002/95/EC RoHS (RESTRICTION OF HAZARDOUS SUBSTANCES) FINISH: EXCEPT AS NOTED REMOVE ALL BURRS BREAK SHARP EDGES . 005/. 010 R SURFACE FINISH INDICATED PER ANSI B46. 1-1985 GENERAL TOLERANCES: 2 DECIMALS ± . 03 3 DECIMALS ± . 015 ANGLES ± 1° FEATURES SHOWN PERPENDICULAR OR PARALLEL SHALL BE SO WITHIN ± 1° REMOVE CARBURIZATIO AND SCALE FROM LASE AND PLASMA CUT EDGE GENERAL MACHINING 125 28 Cybex 18020 Bravo Pull Owner's Manual Return Material Authorization (RMA) The Return Material Authorization (RMA) system is used when returning material for placement, repair or credit. The system assures that returned materials are properly handled and analyzed. Follow the following procedures carefully. [. . . ]