User manual CYBEX INTERNATIONAL BRAVO LIFT

[. . . ] Part Number 18030-999-4 Cybex Bravo Lift Owner's Manual Strength Systems www. cybexintl. com Table of Contents Safety Safety Guidelines And Practices . 3 6 7 8 9 Assembly Machine Specifications. . 18 21 23 24 25 Customer Service Product Registration . . 26 26 27 28 28 Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. [. . . ] Remove front panel from machine. 18030cannotfit through doorway Remove weight stack 1. Remove spiral pin connecting pulley using a hammer and a 3/16" pin punch. Spiral pin 12 Cybex 18030 Bravo Lift Owner's Manual If Then 1. Move pulley and cable connection out of the way. Guide rod cap contains a compression spring that will fly if grasp is not released slowly. Slide spring loaded guide rod cap down guide rod until cap is clear of frame. Slowly release grasp of guide rod cap and remove. Remove the pin spring with a 3/16" punch and hammer securing handle to ball stop and remove handle. Handle 18030Cannotfit through doorway Pin Spring BHSCS/Ball Stop 2. Remove the two Button Head Socket Head Cap Screws (BHSCS) securing the ball stop together with a 1/8"Allen wrench. Remove the BHSCS and locknut securing the pulley using a 7/32" Allen wrench and a 9/16" wrench. BHSCS/ Locknut 4. Move pulley and cable out of the way. Pulley 5. Repeat steps above for opposite handle, ball stop, pulley and cable. 13 Cybex 18030 Bravo Lift Owner's Manual If Then Two people will be required for this procedure Separate frame 1. Remove the eight BHSCS securing the platform to the frame using a 7/32"Allen wrench and a 9/16" wrench. 18030Cannotfit through doorway BHSCS/ Locknut Qty 8 2. Reattach frame halves and securely tighten the BHSCS and locknuts. Securelyanchormachinetothefloor To maximize stability, equipment must be secured to a solid level surface. · Cybex · Use · If is not responsible for the actual anchoring of equipment. tensile capacity (3/8'' grade 2 bolts or better). legs/frame does not contact surface, DO NOT pull down with anchors. Shim any leg or framenotincontactwithsurfaceusingflatwashers. 14 Cybex 18030 Bravo Lift Owner's Manual Install individual weight plates one at at time 1. Position each weight plate so wide edges of bushings face upward and narrow edges of bushings face downward. RE COR CT WRO NG Wide bushing edge faces upward 2. Cable routing The narrow bushing edge must face downward. 1. Place a small amount of loctite® on BHSCS and inside threads of ball stop. Secure cable to ball stop using a 1/8" Allen wrench. Reconnect handle, pulley and cable to platform on both sides. Position pulley mount parallel to the top weight. [. . . ] All parts can be found on the web at www. cybexintl. com Shipping Address Contact Name Include a description of the problem. In addition to your shipping address and contact name, your account number is helpful but not required. You may also fax orders to 508-533-5183. MATERIAL: DIMENSIONS IN INCHES ALL MATERIAL MUST COMPLY TO EUROPEAN UNION DIRECTIVE 2002/95/EC RoHS (RESTRICTION OF HAZARDOUS SUBSTANCES) FINISH: EXCEPT AS NOTED REMOVE ALL BURRS BREAK SHARP EDGES . 005/. 010 R SURFACE FINISH INDICATED PER ANSI B46. 1-1985 GENERAL TOLERANCES: 2 DECIMALS ± . 03 3 DECIMALS ± . 015 ANGLES ± 1° FEATURES SHOWN PERPENDICULAR OR PARALLEL SHALL BE SO WITHIN ± 1° REMOVE CARBURIZATIO AND SCALE FROM LASE AND PLASMA CUT EDGE GENERAL MACHINING 125 27 Cybex 18030 Bravo Lift Owner's Manual Return Material Authorization (RMA) The Return Material Authorization (RMA) system is used when returning material for placement, repair or credit. The system assures that returned materials are properly handled and analyzed. Follow the following procedures carefully. [. . . ]