User manual CYBEX INTERNATIONAL 750C-750R CYCLE

[. . . ] Cybex 750C/750R Cycle Owner's Manual Cardiovascular Systems Part Number LT-21613-4 G www. cybexinternational. com Cybex 750C/750R Cycle Owner's Manual Cardiovascular Systems Part Number LT-21613-4 G Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. Polar® is a registered trademark of Polar Electro Inc. iPOD® is a registered trademark of Apple Inc. DISCLAIMER: Cybex International, Inc. makes no representations or warranties regarding the contents of this manual. [. . . ] Unit will stay locked until UNLOCKED is selected. Gives user capability to SAVE PROG ON (or OFF). (factory default is OFF) create and store custom programs by enabling of disabling SAVE button during Review Mode. 16-Custom Programs SAVE *MAX TIME ZONED If choice is ZONED, choose the actual time for each zone to start and maximum time setting. NOTE: Current Time must be set for zones to work correctly. HH:MM X is the actual time the zone starts, and YYY is the maximum time allowed during time zone. Example: Format ZONE1 HH:MM X YYY ZONE2 HH:MM X YYY ZONE3 HH:MM X YYY ZONE4 HH:MM X YYY Factory Default ZONE1 05:01A ZONE2 09:01A ZONE3 04:01P ZONE4 09:00A 60 OFF 60 OFF Assembly and Setup Page 2­15 Cybex 750C/750R Owner's Manual This page intentionally left blank Assembly and Setup Page 2­16 Cybex 750C/750R Owner's Manual 3 - Operation Intended Use The intended use of this exercise equipment is to aid or improve general physical fitness and exercise. Terms Used Active Mode ­ Any time unit is controlling resistance and accumulating workout data. Active Mode begins after hitting QUICK START during the initial count-down screen, after completing the setup for a program or by default if the initial count-down screen times out and enters Quick Start Manual mode. Auto-Scan ­ Display automatically cycles through workout data. Cool Down ­ A reduction of work load for a short duration allows user to gently reduce heart rate. Cool Down occurs two minutes prior to completion of the program-controlled workout sessions. Dormant Mode ­ Occurs only when a unit is plugged in using the optional AC adapter and is not in use. Isokinetic Exercise ­ Accommodating resistance, where unit provides a corresponding amount of resistance on the user to keep them at a fixed pedal speed. Such exercise is used to test and improve muscular strength and endurance, especially after injury. Manual Mode ­ The unit defaults to this mode if not in a program. Manual Mode allows user to adjust the gear (1-21) and pedal at any speed, simulating a road bike. Time will count up in Quick Start, Manual or Count Down to the chosen session time if user enters a TIME or selects the MANUAL button and completes setup. Pause Mode ­ Occurs only if the Pause feature is enabled and user selects the PAUSE/END key from Active Mode. Program Setup Mode ­ Begins after pressing PROGRAM, ADVANCED or MANUAL key. Upon entering a program, user is prompted to adjust the appropriate settings. Quick Start ­ By default, the unit will end up in Quick Start Manual Mode if the user begins pedalling and allows the 5 second count-down to end. Also choose the QUICK START button to enter into Quick Start Manual Mode, where the user controls the gear selection and time is counting up. Workout Review ­ Review of the accumulated workout data and/or the results of the Fitness Test will happen at the end of each workout session. Operation Page 3­1 Cybex 750C/750R Owner's Manual Read and understand all warnings and cautions in Chapter 1 ­ Safety and all operation instructions in this chapter before operating unit. Mount and Dismount WARNING: Wait until all moving parts come to a complete stop before mounting or dismounting. Verify unit is in Dormant Mode and pedals are completely stopped. [. . . ] Provide the technician with a detailed description of the problem or the defect in the item. The serial number is located on the front of the unit as shown in Figure 1. The serial number begins with a letter, for example: R09-101331100. At Cybex's discretion, the technician may request that the problem part(s) be returned to Cybex for evaluation and repair or replacement. [. . . ]