User manual D-LINK DAP-3410

[. . . ] Version 3. 0 | 21/05/2014 User Manual Wireless N Exterior Access Point DAP-3410 Table of Contents Table of Contents Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Public Port: Enter the port that you want to open for the external network. Note: The private and public ports are usually the same. The public port is the port seen from the Internet side, and the private port is the port being used by the application on the computer or device within your local network. D-Link DAP-3410 User Manual 42 Section 3 - Configuration Parental Control Parental Control is used to allow you to set up a range of IP Addresses that can be either be blacklisted or whitelisted to certain MAC addresses on the network. Active: Select to either Disable or Enable the Parental Control feature. Comment: You can enter a comment here for each rule that is created. MAC Address: Enter the MAC address to be monitored and click Save to add it to the parental control list. Local IP: Enter the start and end of an IP address range that you would like to filter on the local network. This is normally used to prevent access to certain parts of the internal network. Destination IP: Enter the start and end of an IP address range that you would like to filter on the destination network. This is normally used to prevent access to certain parts of the external network. Protocol: Specify which protocol to filter. Local Port: Enter the specific port to filter on the local network. Destination Enter the specific port to filter on the destination Port: network. D-Link DAP-3410 User Manual 43 Section 3 - Configuration Static Routing Setup This page will allow you to configure the built-in routing protocols that the DAP-3410 allows when in certain operating modes. OSPF Service Select to either Disable or Enable the AP from offering OSPF service. RouterID: Select the interface that the AP will broadcast OSPF from. This should be the main interface that will connect to the local network. Network Selecting this checkbox will allow you to enter (Internal): an area that will be used by the static routing setup on the internal network. Network Selecting this checkbox will allow you to enter (External): an area that will be used by the static routing setup on the external network Distribute RIP Enabling this option will allow the router to over OSPF: broadcast the RIP routing protocol over OSPF. RIP Service: Select to either Disable or Enable the AP from offering RIP routing services. Side (Devices): Select the checkbox for the interface that will allow clients to connect to. Distribute Enabling this option will allow the router to broadcast the OSPF routing protocol over the RIP service. OSPF over RIP: Click Create New Route Table to define specific routes that will be handled by the AP. IP Routing D-Link DAP-3410 User Manual 44 Section 3 - Configuration This page will allow you to define specific routes that will be broadcasted by the AP and made available to the clients that connect to it. Mode: Select whether the route being offered is either Disabled or Enabled. Destination Enter either the destination network, or the Net/Mask: subnet mask that will be used in the static route. Via: Select whether the static route will be controlled by an existing gateway, or if the interface on the AP should route the traffic. [. . . ] An Infrastructure network contains an Access Point or wireless bridge. All the wireless devices, or clients, will connect to the wireless bridge or access point. An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc mode to communicate. D-Link DAP-3410 User Manual 85 Appendix B - Networking Basics Networking Basics Check your IP address After you install your adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i. e. [. . . ]