User manual D-LINK DES-1008FX

[. . . ] DES-1008FX 100 Fast Ethernet Switch User's Guide (Draft 2: 01/07/99) Rev. 01 (9, 1997) 6xxxxxxxx. 01 Printed In Taiwan RECYCLABLE WARRANTIES EXCLUSIVE 0-1 IF THE D-LINK PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT D-LINK'S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. D-LINK NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF D-LINK'S PRODUCTS D-LINK SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY THE CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING OR OTHER HAZARD. LIMITATION OF LIABILITY IN NO EVENT WILL D-LINK BE LIABLE FOR ANY DAMAGES, INCLUDING LOSS OF DATA, LOSS OF PROFITS, COST OF COVER OR OTHER INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES ARISING OUT THE INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE OR INTERRUPTION OF A D- LINK PRODUCT, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY. [. . . ] All ports can be selected to perform half-duplex or full duplex connections. Select any of 8 ports for uplink/ MDI-X (media dependent interface) port for uplink to another switch, hub or repeater. Performance features Store and forward switching scheme capability to support rate adaptation and protocol conversion. Introduction 3 Full and Half-duplex at 100Mbps to allow two communicating stations to transmit and receive at the same time. Data forwarding rate 148, 800 pps per port at 100% of fiberspeed. Data filtering rate eliminates all error packets, runts, etc. at 148, 800 pps per port at 100% of fiber-speed. 8K active MAC address entry table per device with selflearning and table aging. Supports broadcast storm rate filtering. 4 Introduction User's Guide 2 2 UNPACKING AND SETUP This chapter provides unpacking and setup information for the Switch. Unpacking Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the following items: One DES-1008FX 100Mbps Fast Ethernet Switch Four rubber feet with adhesive backing 1 AC power cord This user's guide with Registration Card If any item is found missing or damaged, please contact your local D-Link Reseller for replacement. Unpacking and Setup 5 Setup The setup of the Switch can be performed using the following steps: The surface must support at least 3 Kg. The power outlet should be within 1. 82 meters (6 feet) of the device. Visually inspect the power cord and see that it is secured fully to the AC power connector. Make sure that there is proper heat dissipation from and adequate ventilation around the Switch. Do not place heavy objects on the Switch. Desktop or Shelf Installation When installing the Switch on a desktop or shelf, the rubber feet included with the device must be first attached. Attach these cushioning feet on the bottom at each corner of the device. Allow enough ventilation space between the device and the objects around it. 6 Unpacking and Setup User's Guide Figure 1. DES-1008FX Fast Ethernet Switch installed on a Desktop or Shelf Rack Installation The DES-1008FX can be mounted in an EIA standard size, 19-inch rack, which can be placed in a wiring closet with other equipment. To install, attach the mounting brackets on the switch's front panel (one on each side) and secure them with the screws provided. Unpacking and Setup 7 Figure 2A. Attaching the mounting brackets to the DES-1008FX 100Mbps Fast Ethernet Switch Then, use the screws provided with the equipment rack to mount the Switch in the rack. Figure 2B. Installing the DES-1008FX 100Mbps Fast Ethernet Switch in an equipment rack Power on The DES-1008FX Switch can be used with AC power sources 100 240 VAC, 50 - 60 Hz. The power switch is located at the rear of the unit adjacent to the AC power connector and the system fan. The Switch's power supply will adjust to the local power source automatically and may be turned on without having any or all LAN segment cables connected. After the power switch is turned on, the LED indicators should respond as follows: The power LED indicator will turn on and remain ON. . 8 Unpacking and Setup User's Guide Power Failure As a precaution, the Switch should be turned OFF in case of power failure. [. . . ] Please refer to EIA/TIA-568A for detail description. The following diagram and tables show the standard fiber connector SC receptacle/connector and their pin assignments for the switch to network adapter card, switch, hub or bridge connection. The standard fiber connector SC receptacle/connector Fiber Connector SC Pin Specifications 21 SC Fiber Connector pin assignment Contact 1 2 Media Crossover Interface Signal Tx +(transmit) Rx - (receive) The standard SC Fiber Connector pin assignment 22 Fiber Connector SC Pin Specifications User's Guide 7 INDEX 1 100 M (speed indicator) . . . . . . . . . . 13 A AC inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 AC power cord . . . . . . . . . . . . . . . . . . . . . . . . . . 5 D Desktop or Shelf Installation . . . . . 6 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]