User manual D-LINK DES-3010FA

[. . . ] Table of Contents D-Link DES-3010FA/GA User Guide Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Using the Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Using the Embedded Web Interface User Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Intended Audience. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 D-Link DES 3010FA/GA Installation Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Device Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The Add DNS Host Page opens: Click Page 132 Configuring IP Information Configuring Domain Name Servers Figure 81: Add DNS Host Page 3. 4. Define the Host Name and IP Address fields. The DNS host is added, and the device is updated. Page 133 D-Link DES-3010FA/GA User Guide Section 11. Defining the Forwarding Database Packets addressed to destinations stored in either the Static or Dynamic databases are immediately forwarded to the port. The Dynamic MAC Address Table can be sorted by interface, VLAN, or MAC Address, whereas MAC addresses are dynamically learned as packets from sources that arrive at the device. Static addresses are configured manually. An address becomes associated with a port by learning the port from the frame's source address, but if a frame that is addressed to a destination MAC address is not associated with a port, that frame is flooded to all relevant VLAN ports. To prevent the bridging table from overflowing, a dynamic MAC address, from which no traffic arrives for a set period, is erased. This section contains information for defining both static and dynamic forwarding database entries, and includes the following topics: · · Defining Static Forwarding Database Entries Defining Dynamic Forwarding Database Entries Page 134 Defining the Forwarding Database Defining Static Forwarding Database Entries Defining Static Forwarding Database Entries The Forwarding Database Static Addresses Page contains parameters for defining the age interval on the device. To prevent static MAC addresses from being deleted when the device is reset, ensure that the port attached to the MAC address is locked. To configure the static forwarding database: 1. Click Advanced Setup > Forwarding Database > Static Addresses. The Forwarding Database Static Addresses Page opens. Figure 82: Forwarding Database Static Addresses Page The Forwarding Database Static Addresses Page contains the following fields: · · · MAC Address -- Displays the MAC address to which the entry refers. VLAN ID -- Displays the VLAN ID number to which the entry refers. Interface -- Displays the interface to which the entry refers: ­ ­ · ­ ­ ­ ­ Port -- The specific port number to which the forwarding database parameters refer. LAG -- The specific LAG number to which the forwarding database parameters refer. Status -- Displays how the entry was created. The possible field values are: Secure -- The MAC Address is defined for locked ports. Permanent -- The MAC address is permanent. Delete on Reset -- The MAC address is deleted when the device is reset. Delete on Timeout -- The MAC address is deleted when a timeout occurs. Page 135 D-Link DES-3010FA/GA User Guide · Remove -- Removes the entry. The possible field values are: ­ ­ Checked -- Removes the selected entry. Unchecked -- Maintains the current static forwarding database. [. . . ] FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. [. . . ]