User manual D-LINK DGS-3212SR

[. . . ] Vervenden Sie keine Flüssig- oder Aerosolreiniger. 6. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind. Das Gerät is vor Feuchtigkeit zu schützen. Bei der Aufstellung des Gerätes ist auf sichern Stand zu achten. [. . . ] The users will set server hosts in a preferable order in the built-in server group and when a user tries to gain access to the Switch, the Switch will ask the first server host for authentication. If no authentication is made, the second server host in the list will be queried, and so on. The built-in server group can only have hosts that are running the specified protocol. For example, the TACACS server group can only have TACACS server hosts. The administrator for the Switch may set up 6 different authentication techniques per user-defined method list (TACACS / XTACACS / TACACS+ / RADIUS / local / none) for authentication. These techniques will be listed in an order preferable, and defined by the user for normal user authentication on the Switch, and may contain up to eight authentication techniques. When a user attempts to access the Switch, the Switch will select the first technique listed for authentication. If the first technique goes through its server hosts and no authentication is returned, the Switch will then go to the next technique listed in the server group for authentication, until the authentication has been verified or denied, or the list is exhausted. Please note that user granted access to the Switch will be granted normal user privileges on the Switch. To gain access to admin level privileges, the user must enter the enable admin command and then enter a password, which was previously configured by the administrator of the Switch. 160 xStack Gigabit Layer 3 Switch Command Line Interface Manual NOTE: TACACS, XTACACS and TACACS+ are separate entities and are not compatible. The switch and the server must be configured exactly the same, using the same protocol. At that point, the Switch will restart the same sequence with the following protocol listed, xtacacs. If no authentication takes place using the xtacacs list, the local account database set in the Switch is used to authenticate the user. When the local method is used, the privilege level will be dependant on the local account privilege configured on the Switch. Successful login using any of these methods will give the user a "user" privilege only. If the user wishes to upgrade his or her status to the administrator level, the user must implement the enable admin command, followed by a previously configured password. (See the enable admin part of this section for more detailed information, concerning the enable admin command. ) Parameters default ­ The default method list for access authentication, as defined by the user. The user may choose one or a combination of up to four (4) of the following authentication methods: tacacs ­ Adding this parameter will require the user to be authenticated using the TACACS protocol from the remote TACACS server hosts of the TACACS server group list. xtacacs ­ Adding this parameter will require the user to be authenticated using the XTACACS protocol from the remote XTACACS server hosts of the XTACACS server group list. tacacs+ ­ Adding this parameter will require the user to be authenticated using the TACACS+ protocol from the remote TACACS+ server hosts of the TACACS+ server group list. radius - Adding this parameter will require the user to be authenticated using the RADIUS protocol from the RADIUS server listed in the server group list. server_group <string 15> - Adding this parameter will require the user to be authenticated using a user-defined server 164 Description xStack Gigabit Layer 3 Switch Command Line Interface Manual config authen_login group previously configured on the Switch. [. . . ] Restrictions Example usage: To rename a file: DGS-3324SRi:4#ren c:/abc. txt c:/cba. txt Command: ren c:/abc. txt c:/cba. txt Done!!DGS-3324SRi:4# Only administrator-level users can issue this command. rename Purpose Syntax Description Parameters To rename a file. rename <source_path_filename 64> <target_path_filename 64> This command is used to rename a filename located on the storage media accessory. <source_path_filename 64> - Enter the path and name of the file to be renamed. [. . . ]