User manual D-LINK DGS-3224TG

[. . . ] DGS-3224TG Managed 24-Port Gigabit Ethernet Switch User's Guide First Edition (October 2004) 651TG3224015 Printed In Taiwan RECYCLABLE Wichtige Sicherheitshinweise 1. Bitte lesen Sie sich diese Hinweise sorgfältig durch. Heben Sie diese Anleitung für den spätern Gebrauch auf. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. [. . . ] Each port's multicast group membership can be set individually by highlighting the port's entry using the arrow keys, and then toggling between E and ­ using the space bar. · · E (Egress Member) ­ Specifies the port as being a static member of the multicast group. Egress Member Ports are ports that will be transmitting traffic for the multicast group. ­ (Non-Member) ­ Specifies the port as not being a member of the multicast group, but the port can become a member of the multicast group dynamically. Highlight APPLY and press Enter to make the changes current. Use Save Changes from the main menu to enter the changes into NV-RAM. 48 DGS-3224TG Gigabit Ethernet Switch User's Guide Note: The DGS-3224TG supports a maximum of 16K multicast MAC address entities. Configure VLANs The switch reserves one VLAN, VID = 1, called the DEFAULT_VLAN for internal use. The factory default setting assigns all ports on the switch to the DEFAULT_VLAN. As new VLANs are configured, their respective member ports are removed from the DEFAULT_VLAN. If the DEFAULT_VLAN is reconfigured, all ports are again assigned to it. Ports that are not wanted as part of the DEFAULT_VLAN are removed during the configuration. If a member of one VLAN wants to connect to another VLAN, it must be through a router. Note: The switch's default is to assign all ports to a single 802. 1Q VLAN named DEFAULT_VLAN. As new VLANs are created, the member ports assigned to the new VLAN will be removed from the default VLAN port member list. An IP interface called System in the IP interface entry menu also has a VID = 1, and therefore corresponds to the DEFAULT_VLAN. Note: To create a new 802. 1Q VLAN: The VLAN menu adds an entry to edit the VLAN definitions and to configure the port settings for IEEE 802. 1Q VLAN support. Highlight Configure VLANs from the Configuration menu and press Enter. Figure 6-21. IEEE 802. 1Q VLANs Configuration menu 802. 1Q Static VLAN Settings To create an 802. 1Q VLAN, highlight Configure Static VLAN Entry and press Enter: 49 DGS-3224TG Gigabit Ethernet Switch User's Guide Figure 6-22. 802. 1Q Static VLAN Settings screen To create an 802. 1Q VLAN, enter a VLAN ID number in the VID field and a name for the new VLAN in the VLAN Name field. To set the 802. 1Q VLAN membership status of a port: To enter the 802. 1Q VLAN status for a port, highlight the first field of Egress/Forbidden. Each port's 802. 1Q VLAN membership can be set individually by highlighting the port's entry using the arrow keys, and then toggling among E, F, and ­ using the space bar. · E (Egress Member) ­ Specifies the port as being a static member of the VLAN. Egress Member Ports are ports that will be transmitting traffic for the VLAN. These ports can be either tagged or untagged. F (Forbidden Non-Member) ­ Defines the port as a non-member and also forbids the port from joining a VLAN dynamically. [. . . ] 29 Saving Changes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13, 23 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 sniffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]