User manual D-LINK DI-300

[. . . ] Copyright Statement Copyright ©1997 D-Link Corporation No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems Inc. , as stipulated by the United States Copyright Act of 1976. Trademarks D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to their respective owners. Limited Warranty This guide and the accompanying product are each provided "as is, " without warranty as to their performance, merchantability or fitness for any particular purpose. D-Link Corporation and D-Link Systems, Inc. reserve the right to revise this publication and to make changes to its contents at any time, without obligation to notify any person or entity of such revisions or changes. Table of Contents INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Keep in mind that these filter set(s) will only apply to all Remote Dial-in Users but not the Remote Nodes. You can choose from 12 different filter sets. In addition, you can link up to 4 filter sets together for further customization (e. g. , 1, 5, 9, 12). Note that spaces and commas are accepted in this field. For more information on customizing your filter sets, see the Filter Configuration chapter on page 96. 18. Session Options: Idle Timeout--This value is the number of idle seconds that elapses before the dial-in user is Dial-In Configuration 65 automatically disconnected. Idle Timeout is the period of time when there is no data traffic between the dial-in user or Remote Node and the router. Authen is set to None and the call is not mapped to any Remote Node or Remote Dial-in User, or the router calls back to the Remote Dial-in User. Once you have completed filling in Menu 13--Default Dial-in Setup, press ENTER at the message `Press ENTER to Confirm. . . ' to save your selections, or press ESC at any time to cancel your selections. Dial-In Users Setup The following steps describe the setup procedure for adding a Remote Dial-in User. From the Main Menu, enter 14 to go to 14. Dial-in User Setup is shown below: 66 Dial-In Configuration Select one of eight users by number, this will bring you to the next screen, Menu 14. 1 - Edit Dial-in User. 1. This will be used as the login name for authentication. Choose a descriptive word for login, e. g. , kathyg. Active--You can disallow dial-in access to this user by setting this field to Inactive. When set to inactive, the user record is still kept in the database for later activation. Deactivated users are displayed with a--(minus sign) at the beginning of the name in Menu 14. Password--Enter the password for the Remote Dial-in User. Callback--This field determines if the DI-300 or DI-300M will allow callback to the Remote Dial-in User upon dial-in. If this control is set to Optional, the router will be able to call back to the Remote Dial-in User if so requested by that user's system; if the control is set to Mandatory, the router will attempt callback in all cases. Callback entails disconnecting Dial-In Configuration 67 the call and dialing the specified callback number (see below). The default setting of this control is No. Phone # Supplied by Caller--This control allows the Remote Dial-in User to specify the callback telephone number on a call-by-call basis. [. . . ] Often used for obtaining device configuration files or bootstrap image files. An SNMP request that managed network devices send to network management stations, to inform them that some problem has been detected. Wire such as is commonly used with telephones consisting of pairs of copper wire 155 STP TCP/IP Telnet TFTP Trap Twisted-pair Glossary usually terminating in an RJ-45 connector. UDP UTP WAN User Datagram Protocol; part of the TCP/IP suite of protocols. [. . . ]