User manual D-LINK DI-704

[. . . ] DI-704 User Manual RECYCLABLE Printed in Taiwan LIMITED WARRANTY D-Link Systems, Inc. ("D-Link") provides this limited warranty for its product only to the person or entity who originally purchased the product from D-Link or its authorized reseller or distributor. Limited Hardware Warranty: D-Link warrants that the hardware portion of the D-Link products described below ("Hardware") will be free from material defects in workmanship and materials from the date of original retail purchase of the Hardware, for the period set forth below applicable to the product type ("Warranty Period") if the Hardware is used and serviced in accordance with applicable documentation. Product Type Product (excluding power supplies and fans), if purchased and delivered in the fifty (50) United States, or the District of Columbia ("USA") Product purchased or delivered outside the USA Power Supplies and Fans Spare parts and spare kits II Warranty Period As long as the original purchaser still owns the product One (1) Year One (1) Year Ninety (90) days D-Link's sole obligation shall be to repair or replace the defective Hardware at no charge to the original owner. Such repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement Hardware need not be new or of an identical make, model or part; D-Link may in its discretion may replace the defective Hardware (or any part thereof) with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware. [. . . ] Rear Panel Figure 2-2 Rear Panel WAN COM Power WAN port socket (RJ-45). This is where you will connect to your cable (or DSL) modem or Ethernet router. Serial port connector (9-pins D-type male). This is where you will connect your modem. This is where you connect the included power adapter. Note that, the included power adapter is DC 5V/1A. Using the wrong type of power adapter may cause damage to the DI-704. 2. 2 Installation Requirements The DI-704 can be positioned at any convenient place in your office or house. No special wiring or cooling requirements is needed. However, you should comply with the following guidelines to install: !Place the DI-704 on a flat horizontal surface. Keep the DI-704 away from excessive heat. Do not place the DI-704 in a dusty or wet environment. The recommended operational specifications of DI-704 are: Temperature Humidity 0 oC ~ 55 oC 5 % ~ 90 % In addition, remember to turn off the power, remove the power cord from the outlet, and keep your hands dry when you install the DI-704. 4 2. 3 Procedure for Hardware Installation 1. Setup LAN connection: connect an Ethernet cable from your computer's Ethernet port to one of the LAN ports of the DI-704. Figure 2-3 Setup of LAN connections for DI-704. Setup WAN connection: prepare an Ethernet cable for connecting the DI-704 to your cable/xDSL modem or Ethernet backbone. Figure 2-4 illustrates the WAN connection. Figure 2-4 Setup of WAN connections for DI-704. Power on: Connect the power cord to power inlet and turn the power switch on. The DI-704 will automatically enter the self-test phase. When in the self-test phase, the indicators M1 and M2 will be lighted ON for about 5 seconds, and then M1 and M2 will flash three times to indicate that the self-test operation has finished. Finally, the M1 will flash continuously once per second to indicate that the DI-704 is in normal operation. 5 Chapter 3 Network Settings The default IP address of the DI-704 is 192. 168. 0. 1, and the default subnet mask is 255. 255. 255. 0. These addresses can be changed to meet your need, but the default values are used in this manual. If the TCP/IP environment of your computer has not yet been configured, you can refer to Appendix B to configure it. configure IP as 192. 168. 0. 2, subnet mask as 255. 255. 255. 0 and gateway as 192. 168. 0. 1, or, 2. [. . . ] Supposing you have successfully installed one network card on your personal computer. If not, please refer to your network card manual. Moreover, the Section B. 2 tells you how to set TCP/IP values for working with the DI-704 correctly. B. 1 Install TCP/IP Protocol into Your PC 1. [. . . ]