User manual D-LINK DI-804V

[. . . ] D-Link DI-804V Broadband VPN Router Manual Rev. 020205 Building Networks for People Contents Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 IP Address Settings and Computer Settings . . . . . . . . . . . . [. . . ] Gateway IP Address The IP address of the interface used to link to the remote network. Dynamic Routing Dynamic Routing Settings allow the VPN Internet Gateway to route IP packets to another network automatically. The RIP protocol is applied, and broadcasts the routing information to other routers on the network regularly. 22 For the SEND option choosing the proper protocol by which you transmit the data on the network. For the RECEIVE option choosing the proper protocol by which the VPN Internet Gateway receive the data on the network. Filter Settings ­ LAN Filter Settings LAN Filter Settings allow administrator to define whether local user has the permission to access Internet. To activate this feature, check LAN Side Filter Enabled. Then, you can define the filtering policy by entering an IP address range, network port number and select the protocol(s). For example, to prevent the local user of IP address range (from 192. 168. 0. 100 to 192. 168. 0. 200) to access port 80 (HTTP), the settings are as follows, LAN Side Filter Enabled: Enabled Default LAN Side Filter: Pass Filter: Block Protocol: TCP IP Address Range: 101 ~ 200 Destination Port Range: 80 ~ 80 (HTTP) 23 Filter Settings ­ WAN Filter Settings WAN Filter Settings allow administrator to define whether remote/outside user has the permission to access the local network. To activate this feature, check WAN Side Filter Enabled. Then, you can define the filtering policy by entering IP address range, the port range and select the protocol(s). For example, to prevent the remote user of IP address range (211. 21. 0. 1 to 211. 29. 0. 1) to access virtual WEB server (port 80), the setting are as follows, WAN Side Filter Enabled: Enabled Default WAN Side Filter: Pass Filter: Block Protocol: TCP IP Address Range: 211. 21. 0. 1 to 211. 29. 0. 1 Destination Port Range: 80 ~ 80 (HTTP) Modem String Settings 24 Modem string settings allow user to input detail settings for the analog modem. If you would like to change the baud rate settings, please check the initial string. (You can refer to the manual for your modem. ) Administration Settings PASSWORD SETTINGS You can give your VPN Gateway a new password. This password will be required the next time you configure your VPN Gateway. To enter a password, type your password in the new password field and type it again in the retype password field. Note: it is important to remember your password. If for any reason you lose or forget your password, press the small reset button located on the back of the device for 5 to 6 seconds. Reset action will re-initialize the settings. All configurations, including password, will be reset and require re-entering. 25 SYSTEM ADMINISTRATION Here, remote users can be set up to configure and administrate the VPN Internet Gateway through Internet. The default IP address of remote administration host is: 0. 0. 0. 0. (IP address of 0. 0. 0. 0 means that any PC on the network can remote access and manage the VPN Internet Gateway). If you use this function, you have to enable the feature "Allow remote user to configure the device" first. Once you have enabled this function, type the VPN Internet Gateway WAN IP address (http://192. 168. 100. 1:1023) into the browser of any or specific PC 26 Note: Once HTTP port no (NOT PORT 80) is changed and the users of the LAN terminal want to configure the VPN Internet Gateway, the users have to type the VPN Internet Gateway LAN IP address with port number (http://192. 168. 0. 1:1023). System Parameters System Parameters allows user to setup the MTU value (Maximum Transmission Unit). User can setup a proper MTU for your network device. For some areas, the ISPs set the limit packet size for PPPoE connection. User has to change MTU setting for surfing the net. 27 Save & Restart If you have finished making all the changes on the various pages, please click Save & Restart to save the settings and restart the device. [. . . ] Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED "AS-IS" WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT. Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK'S PRODUCT IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT. [. . . ]