User manual D-LINK DXS-3250

[. . . ] CLI Guide Product Model : DXS-3200 Series L2 Stackable Gigabit Mngd. Switch with Optional 10Gig Uplinks Release 1 ©Copyright 2005. All rights reserved. Table of Contents Section 1. Using the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 CLI Command Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines Eight aggregated links can be defined with up to eight member ports per port-channel. The aggregated links' valid IDs are 1-8. Example The following example enters the context of port-channel number 1. Console(config)# interface port-channel 1 Page 200 Port Channel Commands interface range port-channel The interface range port-channel Global Configuration mode command enters the interface configuration mode to configure multiple port-channels. Syntax interface range port-channel {port-channel-range | all} Parameters port-channel-range -- List of valid port-channels to add. Separate nonconsecutive port-channels with a · · comma and no spaces. A hyphen designates a range of port-channels. all -- All valid port-channels. Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines Commands under the interface range context are executed independently on each interface in the range. Example The following example groups port-channels 1, 2 and 6 to receive the same command. Console(config)# interface range port-channel 1-2, 6 Page 201 D-Link CLI Reference Guide channel-group The channel-group Interface Configuration (Ethernet) mode command associates a port with a port-channel. To remove a port from a port-channel, use the no form of this command. Syntax channel-group port-channel-number mode {on | auto} no channel-group Parameters · port-channel_number -- Specifies the number of the valid port-channel for the current port to join. · on -- Forces the port to join a channel without an LACP operation. · auto -- Allows the port to join a channel as a result of an LACP operation. Default Configuration The port is not assigned to a port-channel. Command Mode Interface Configuration (Ethernet) mode User Guidelines There are no user guidelines for this command. Example The following example forces port 1/1 to join port-channel 1 without an LACP operation. Console(config)# interface ethernet 1/1 Console(config-if)# channel-group 1 mode on Page 202 Port Channel Commands show interfaces port-channel The show interfaces port-channel Privileged EXEC mode command displays port-channel information. Syntax show interfaces port-channel [port-channel-number] Parameters · port-channel-number -- Valid port-channel number. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays information on all port-channels. Console# show interfaces port-channel Channel ------1 2 3 Ports --------------------------------Active: 1/1, 2/1 Active: 2/1, 2/7 Inactive: 3/1 Active: 3/1, 3/8 Page 203 D-Link CLI Reference Guide Section 17. Port Monitor Commands port monitor The port monitor Interface Configuration mode command starts a port monitoring session. To stop a port monitoring session, use the no form of this command. Syntax port monitor src-interface [rx | tx] no port monitor src-interface Parameters src-interface--Valid Ethernet port. (Full syntax: unit/port) · · rx--Monitors received packets only. · tx--Monitors transmitted packets only. Default Configuration Monitors both received and transmitted packets. Command Mode Interface Configuration (Ethernet) mode User Guidelines This command enables traffic on one port to be copied to another port, or between the source port (src-interface) and a destination port (port being configured). The following restrictions apply to ports configured as destination ports: The port cannot be already configured as a source port. The port cannot be a member in a port-channel. An IP interface is not configured on the port. [. . . ] Console(config-if)# dot1x auth-not-req Page 458 802. 1x Commands dot1x multiple-hosts The dot1x multiple-hosts Interface Configuration mode command enables multiple hosts (clients) on an 802. 1Xauthorized port, where the authorization state of the port is set to auto. To return to the default configuration, use the no form of this command. Syntax dot1x multiple-hosts no dot1x multiple-hosts Default Configuration Multiple hosts are disabled. Command Mode Interface Configuration (Ethernet) mode User Guidelines This command enables the attachment of multiple clients to a single 802. 1X-enabled port. In this mode, only one of the attached hosts must be successfully authorized for all hosts to be granted network access. If the port becomes unauthorized, all attached clients are denied access to the network. [. . . ]