User manual D-LINK GO-DSL-N150

[. . . ] Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1 1. 2 1. 3 1. 4 2 3 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 LEDs and Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You may establish at most sixteen QoS rules. You may select Activated or Deactivated. The QoS rule can be set if it is activated. Support application options such as IGMP, SIP, H. 323, MGCP, SNMP, DNS, DHCP, RIP, RSTP, RTCP and RTP. Description QoS, you may set the upload bandwidth of the WAN 37 GO-DSL-N150 User Manual Field Range Type of Service DSCP Range Select this option to Activate/Deactivated the 802. 1p. IEEE 802. 1p establishes eight levels of priority (0 ~ 7). Although network managers must determine actual mappings, IEEE has made broad recommendations. Seven is the highest priority which is usually assigned to network-critical traffic such as Routing Information Protocol (RIP) and Open Shortest Path First (OSPF) table 802. 1p updates. Five and six are often for delay-sensitive applications such as interactive video and voice. Data classes four through one range from controlled-load applications such as streaming multimedia and business-critical traffic - carrying SAP data, for instance down to "loss eligible" traffic. Zero is used as a best-effort default priority, invoked automatically when no other value has been set. Queue # Select Low, Medium, High or Highest. Support services including Normal service, Minimize delay, Maximize throughput, Maximize reliability and Minimize monetary cost. Description In the above page, click Add to save the discipline. To view the rules and actions, click QoS Settings Summary to enter the page shown in the following figure appears. 38 GO-DSL-N150 User Manual 3. 5. 5 VLAN Choose Advanced Setup > VLAN, the page shown in the following figure appears. Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments. Because VLANs are based on logical instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource optimization. In the VLAN page, click Assign VLAN PVID for each Interface, and the page shown in the following figure appears. 39 GO-DSL-N150 User Manual The following table describes the parameters of this page: Field Description Each physical port has a default VID called PVID (Port PVID VID). PVID is assigned to untagged frames or priority tagged frames (frames with null (0) VID) received on this port. ATM VC # Ethernet Port # Wirelss LAN Next Assign the PVID to Wireless LAN. Click it to go the the VLAN Group Setting page. Assign the PVID to Ethernet Ports. In the VLAN page, click VLAN Group Setting, and the page shown in the following figure appears. 40 GO-DSL-N150 User Manual The following table describes the parameters of this page: Field VLAN Index Active VLAN ID ATM VCs Ethernet Wireless LAN Save Delete Cancel Click it to save the settings. Click it to delete the current group setting. [. . . ] This page that is displayed contains Administration, Time Zone, Firmware, SysRestart and Diagnostics. 65 GO-DSL-N150 User Manual Administration There is only one account that can access Web-Management interface. In this web page, you can set new password for admin. Time Zone The system time is the time used by the device for scheduling services. You can manually set the time or connect to a NTP (Network Time Protocol) server. If a NTP server is set, you will only need to set the time zone. [. . . ]