User manual D-LINK GO-SW-16G

[. . . ] D-Link® GO-SW-16G GO-SW-24G 16/24-PORT GIGABIT EASY DESKTOP SWITCH Manual Building Networks for People RECYCLABLE (December 2013) V 2. 00 D-Link GO-SW-16G/GO-SW-24G GIGABIT EASY DESKTOP SWITCH Information in this document is subject to change without notice. Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. [. . . ] This way, a port connected to a 20m cable only uses as much power as it needs, instead of using full power, which is only needed for 100m cables. Front-Panel Components On the front panel of the Switch you will see the following. • • • LED status indicators 16 Auto-Negotiating 10/100/1000Mbps ports on the GO-SW-16G 24 Auto-Negotiating 10/100/1000Mbps ports on the GO-SW-24G GO-SW-16G Front Panel GO-SW-24G Front Panel LED Indicators The LED indicators of the Switch include a Power status indicator and Link/Act/Speed indicator for each port. LED Indicators 11 LED Indicator Power Description This lights green while the Switch is receiving power. When connected to a 1000Mbps device, this LED indicator light is green when the port is connected to a device and will blink as data is transmitted or received. When connected to a 10/100Mbps device, this LED indicator light is amber when the port is connected to a device and will blink as data is transmitted or received. Link/Act/Speed 12 Rear Panel Description The power cable connection is located on the rear panel of the Switch. DC Power Jack: Power is supplied through an external 12V/1A AC power adapter for GO-SW-16G and an external 12V/1. 5A AC power adapter for GO-SW24G. Check the technical specification section for information about the AC power input voltage. • GO-SW-16G GO-SW-16G Rear Panel • GO-SW-24G GO-SW-24G Rear Panel 10/100/1000BASE-T Ports: There are 16/24 Gigabit Ethernet, Auto-Negotiating ports (10/100/1000Mbps) Comprehensive LED indicators display the conditions of the Switch and status of the network. 13 SECTION 2 Installation Package Contents Before You Connect to the Network Installing the Switch Power On Package Contents Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the following items: • • • • One GO-SW-16G 16-Port/ GO-SW-24G 24-Port 10/100/1000BASE-T GIGABIT EASY DESKTOP SWITCH One AC power adapter Quick Install Guide Wall-mounting kits If any item is found missing or damaged, please contact your local D-Link reseller for replacement. 14 Before You Connect to the Network The site where you install the Switch may greatly affect its performance. Please follow these guidelines for setting up the Switch. • Install the Switch on a sturdy, level surface that can support at least 3 kg (6. 6 lbs. ) of weight. Do not place heavy objects on the Switch. The power outlet should be within 1. 82 meters (6 feet) of the Switch. Visually inspect the power cord and see that it is fully secured to the AC power port. Make sure that there is adequate space for proper heat dissipation from and adequate ventilation around the Switch. Leave at least 10 cm (4 inches) of space at the front and rear of the Switch for ventilation. Install the Switch in a fairly cool and dry place for the acceptable temperature and humidity operating ranges. Install the Switch in a site free from strong electromagnetic field generators (such as motors), vibration, dust, and direct exposure to sunlight. When installing the Switch on a level surface, attach the rubber feet to the bottom of the device. The rubber feet cushion the Switch, protect the casing from scratches, and prevent it from scratching other surfaces. • • • • • • 15 Mounting the Switch on a Rack The GO-SW-16G /24G can be mounted on a wall. Two mounting slots are provided on the bottom of the switch for this purpose. Please make sure that the front panel is exposed in order to view the LEDs. Please refer to the illustration below: A. ) Mounting on a cement wall 1. [. . . ] RJ-45 – Standard 8-wire connectors for IEEE 802. 3 10BASE-T networks. Subset of SNMP MIB II, which allows monitoring and management capabilities by addressing up to ten different groups of information. A device that provides a backup source of power when connected to the Switch. Server Farm – A cluster of servers in a centralized location serving a large user population. [. . . ]