User manual DA-LITE SCB-200

[. . . ] Improper voltage connection will result in SCB-200 damage. Fused protection: 5A Optional Accessories: NET-200 Ethernet Controller WC-200 Wall Controller IR-200 Infrared Sensor RM-200 Infrared Remote Control 2 Installation < WARNING: This product possesses high voltage when connected, and may present a shock hazard when the screen cover is removed. Please disconnect power when performing connections or servicing. > The SCB-200 is installed as a factory option when ordering the compatible screen from Da-Lite. [. . . ] Please note that voltage must be specified at time of order. Improper voltage connection will result in SCB-200 damage. This termination should only be performed by a licensed electrician. 5 Configuration The SCB-200 comes pre-configured in MASTER mode, meaning that it is intended to be used without connection to other SCB-200 devices. If multiple SCB-200 are planned for use in a configuration, each must posses an independent RS-485 address. To change the address, DIP switches are provided on the SCB-200. Up to eight SCB-200 devices may be ganged together and independently addressed. Please reference the following DIP switch table for addressing each unit. Mode Master Slave 1 Slave 2 Slave 3 Slave 4 Slave 5 Slave 6 Slave 7 1 * * * * * * * * 2 0 0 0 0 1 1 1 1 3 0 0 1 1 0 0 1 1 4 0 1 0 1 0 1 0 1 * Please note that DIP 1 should be in the "1" position for SCB-200 devices at each end of the daisy-chain. DIP 1 should be in the "0" position for all remaining (intermediary) SCB-200 devices. Figure 5 - Address DIP Switches The SCB-200 is designed for automatic configuration and has a factory calibrate mode that "learns" the screen's mechanical limits and stores them in non-volatile memory, so that in the event of power loss or disconnection, the calibrated settings are retained. In the event that the screen mechanical stops are adjusted or other mechanical alterations are made to the screen, the factory calibrate mode must be performed again. Contact Da-Lite technical support for more information on this procedure. Upon power up of the SCB-200, it shall immediately begin a diagnostic mode routine that verifies settings and prepares the controller for operation. During this process, the following activities shall occur: 6 - Load of relevant settings from EEPROM into SCB-200 memory Auto-detection of the presence of an optional NET-200 daughterboard Initiation of the optional NET-200 settings The power up mode shall remain in effect until each of these activities is completed. The SCB-200 will not accept or process communications with any I/O port while in this state. During the initial configuration of the SCB-200, the following parameters may be set, using the RS-232 protocol identified in Appendix A. Set DHCP Support * Set Custom Aspect Ratios Set IP Address * * Denotes configuration settings related to use with optional NET-200 daughterboard. Refer to the NET-200 user manual for configuration of these parameters. When setting custom aspect ratios, the screen is positioned in the desired position, and the position is stored to a desired custom preset memory position. There are five available memory positions for custom aspect ratios. When recalling aspect ratios, the SCB-200 is aware of the physical aspect ratio of the screen. Any command that requests an aspect ratio beyond the physical limitations of the screen will result in the screen being set to its lowest position. When adjusting aspect ratio, the screen is positioned according to the image centerline. [. . . ] ID GE ST [numeric value]<CR> Get Screen Width # ID GE SW<CR> Gets the current SW value ACK: !ID SE TA OK<CR> Set Screen Position, in Inches # ID SE IN [FIX, INC, DEC] [numeric value]<CR> Sets the IN value ACK: !ID SE IN OK<CR> Set Screen Position, in MM # ID SE MM [FIX, INC, DEC] [numeric value]<CR> Sets the MM value ACK: !ID SE MM OK<CR> Set Custom Aspect Ratio # ID SE A[6-0] <CR> Sets the A[6-0] value to the current position ACK: ! [. . . ]