User manual DA-LITE TENSIONED ADVANTAGE ELECTROL

[. . . ] Tightenboltsuntiltrimflangeisflushwithceiling. NOTE: For proper operation, screen assembly must be level after installation. NOTE: Must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC), CAN/CSA C22. 1 and the National Electric Code (NEC), NFPA 70. nstallelectricalconnectionsthatappliestoyourunit. Makesuretoreviewthewiringdiagramforproperhookup. [. . . ] U se2-conductor20-24gaugewiretoextendthelowvoltageconnectionfrom theprojector's5or12-voltscreentriggeroutputtothelengthrequiredtoreach theVPI. Whenextendingthelowvoltageconnectionfromtheprojector'sscreen triggeroutputpolaritydoesnotmatter. TheredandblackwiresfromtheVPIare interchangeable. LED UPLIMIT TACTILE BUTTON RJ-22 INPUTS RJ-22JACK RJ-22OUTPUT DRYCONTACTS DOW N DOWN LIMIT TACTILE BUTTON BACKOF WALLSWITCH RJ-45 JACK RJ-45 RECEPTACLE DATA CABLE FRONTOF WALLSWITCH POWER WIRE BLACK RED IMPORTANT NOTE: ThewallswitchisREQUIREDtomakeanylimitswitchadjustments, EVENifathirdpartycontrolsystemisused. Therefore, itisadvisedto wiretheswitchorprovidea3-conductorconnectionthatisaccessible. 5/12VOLTSCREEN TRIGGERONPROJECTOR VPITRIGGER MODULE BLACK(HOT) WHITE(COMMON) GREEN(GROUND) GROUND­MUSTBECONNECTED TOBUILDINGGROUND POWER INPUT 120VAC / 60HZ FIGURE4 3 TENSIONED ADVANTAGE® ELECTROL® INSTALLATION FOR 120V SCREENS RJ-14 PIN-OUTS (TAB IS FACING UP) WHITE GREEN RED BLACK BUS (RP DATA) RQ DATA +5V GND 120V WIRING DIAGRAM WITH OPTIONAL BUILT-IN LOW VOLTAGE CONTROL LED RJ-22 JACK RJ-22 OUTPUT RJ-22 PIN-OUTS (TAB IS FACING UP) +12V BUS (RP DATA) RQ DATA +5V GND RQ CLOCK BLUE YELLOW GREEN RED BLACK WHITE Supplied RJ-14 cable Standard RJ-22 can be used in place of RJ-14 UP DO (RED WN ) (BL M AC (W HIT K) E) UP LIMIT TACTILE BUTTON RJ-22 JACK RJ-22 INPUTS RJ-45 PIN-OUTS DRY CONTACTS (TAB IS FACING UP) MANUAL 2 +12V BUS (RP DATA) RQ DATA +5V GND BROWN BLUE YELLOW GREEN RED BLACK ORANGE PURPLE CO UP STO P DOW N DOWN LIMIT TACTILE BUTTON RJ-45 JACK RJ-45 RECEPTACLE RQ CLOCK DATA CABLE MANUAL 1 FRONT OF WALL SWITCH BACK OF WALL SWITCH POWER WIRE IMPORTANT NOTE: ThewallswitchisREQUIREDtomakeanylimitswitch adjustments, EVENifathirdpartycontrolsystemis used. Therefore, itisadvisedtowiretheswitchor providea3-conductorconnectionthatisaccessible. GREEN (GROUND) BLACK (HOT) WHITE (COMMON) POWER INPUT 120VAC / 60HZ GROUND­MUST BE CONNECTED TO BUILDING GROUND FIGURE 5 4 TENSIONED ADVANTAGE® ELECTROL® INSTALLATION FOR 220/240V SCREENS 240V WIRING DIAGRAM WITH OPTIONAL BUILT-IN VIDEO PROJECTOR INTERFACE BROWN(HOT) BLUE(COMMON) GREEN/YELLOW(GROUND) BROWN(DOWN) BLUE(COMMON) BLACK(UP) 240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH: Da-Liteofferstwostylesof240voltwall switchesforstandardoperation. Pleasesee wiringdiagramincludedinwallswitchbox includedwithscreen. 240VOLTAC/50HZ POWERSOURCE GREEN/YELLOW(GROUND) FRONTOF WALLSWITCH UP STOP DOWN RED BLACK WHITE BACKOFWALL SWITCH FIGURE 6 RED BLACK 5/12VOLTSCREEN TRIGGERONPROJECTOR FIGURE 7 CAUTION: THE PROJECTOR MUST BE TURNED OFF BEFORE CONNECTING THE TRIGGER WIRES TO THE PROJECTOR. FAILURE TO DO SO MAY DAMAGE THE CONTROLLER. Use2-conductor20-24gaugewiretoextendthelowvoltageconnectionfromtheprojector's5or12-voltscreen triggeroutputtothelengthrequiredtoreachtheVPI. Whenextendingthelowvoltageconnectionfromthe projector'sscreentriggeroutput, besuretomaintaintheproperpolarity. TheredwirefromtheVPIisthe"signal" andtheblackwirefromtheVPIisthe"ground" . ConnectthewiresfromtheVPIthatarelabeled"LowVoltageConnection"totheendoftheextendedscreen triggerwiresabove. !s 240V WIRING DIAGRAM WITH OPTIONAL BUILT-IN LOW VOLTAGE CONTROL BLUE (COMMON) BROWN (HOT) 240VAC 50HZ GREEN OPTIONAL IR AND RF REMOTE CONTROL LOW-VOLTAGE WALL SWITCH UP DN UP GND +5V MOTOR RJ9 RJ9 STOP DOWN 3-POSITION SWITCH RJ9 GROUND TO CASE UP +5V COM DN GROUND­MUST BE CONNECTED TO BUILDING GROUND GREEN FRONT BACK SPLITTER DRY CONTACTS ILT RJ9 PIN-OUTS (TAB IS FACING UP) IR or UP GND COMMON +5V DN or DATA BLACK RED GREEN WHITE IMPORTANT NOTE:ThewallswitchisREQUIREDtomakeanylimit switchadjustments, EVENifathirdpartycontrol systemisused. Therefore, itisadvisedtowirethe switchorprovidea4-conductorconnectionthatis accessible. FIGURE 8 5 SCREEN ADJUSTMENT FOR 120V SCREENS WITHOUT BUILT-IN LOW VOLTAGE CONTROL Surfacetravelisstoppedautomaticallyinthefullyopenedandclosedpositionsbylimitswitchesthatareproperly adjustedatDa-Lite. Shoulditbenecessarytoadjustformoreorlessdropofpicture, proceedinthefollowingmanner: Removetwoscrewstoremoveaccessdoor. NOTE:Useascrewdriveror5/32"Allenwrenchtomakeadjustments. Placeoperatingswitchin"down"position. henthescreenstops, turnthewhite"down"limitknob(Fig. 1)oneturncounterclockwise. Testbyraisingpicture W surfaceapproximatelytwofeet, thenloweragain. Repeatuntildesiredpicturesurfacepositionisattained. aisepicturesurfaceapproximately R twofeetabovedesiredlevel. laceoperatingswitchin"off" P position. urnthewhite"down"limitknob T (Fig. 1)oneturnclockwise. Testby raisingpicturesurface approximatelytwofeet, thenlower again. Repeatuntildesiredpicture surfacepositionisattained. WHITE ADJUSTMENT KNOB "DOWN" MOTOR POWER CONNECTOR MOTOR MOTOR MOUNT BRACKET BLACK ADJUSTMENT KNOB "UP" FIGURE 1 SCREEN ADJUSTMENT FOR 220/240V SCREENS WITHOUT BUILT-IN LOW VOLTAGE CONTROL Surfacetravelisstoppedautomaticallyinthefullyopenedandclosedpositionsbylimitswitchesthatareproperly adjustedatDa-Lite. Shoulditbenecessarytoadjustformoreorlessdropofpicture, proceedinthefollowingmanner: NOTE:Useascrewdriveror5/32"Allenwrenchtomakeadjustments. Placeoperatingswitchin"down"position. henthescreenstops, turnthewhite "down"limitknob(Fig. 2)oneturncounterclockwise. Testbyraisingpicture W surfaceapproximatelytwofeet, thenloweragain. Repeatuntildesiredpicturesurfacepositionisattained. aisepicturesurfaceapproximately R twofeetabovedesiredlevel. laceoperatingswitchin"off" P position. urnthewhite"down"limitknob T (Fig. 2)oneturnclockwise. Testby raisingpicturesurface approximatelytwofeet, thenlower again. Repeatuntildesiredpicture surfacepositionisattained. MOTOR POWER CONNECTOR MOTOR WHITE ADJUSTMENT KNOB "DOWN" MOTOR MOUNT BRACKET RED ADJUSTMENT KNOB "UP" FIGURE 2 6 SCREEN ADJUSTMENT FOR 120V SCREENS WITH A BUILT-IN LOW VOLTAGE CONTROL OR VPI 1. Locatethewallswitchandremovethecoverplatefromthe3-buttonwallswitchandremovetheswitchfromthe junctionbox. Locatethetwotactilebuttonsonthebackoftheswitch. Theyaresquaresilverwithblackroundbuttons. See Figure4(VPI)orFigure5(LVC)fordiagram. [. . . ] N NOTE: Screen will operate with a low-pitched hum. 4. F (c) Fabricisdamaged. 8 9 10 LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS Da-LiteScreenCompany, Inc. warrantsitsproductstotheoriginalpurchaseronly, tobefreefrom defectsinmaterialsandworkmanshipforaperiodofone(1)yearfromthedateofpurchaseby theoriginalpurchaserprovidedtheyareproperlyoperatedaccordingtoDa-Lite'sinstructionsand arenotdamagedduetoimproperhandlingortreatmentaftershipmentfromthefactory. Thiswarrantydoesnotapplytoequipmentshowingevidenceofmisuse, abuseoraccidental damage, orwhichhasbeentamperedwithorrepairedbyapersonotherthanauthorizedDa-Lite personnel. Da-Lite'ssoleobligationunderthiswarrantyshallbetorepairortoreplace(atDa-Lite'soption) thedefectivepartofthemerchandise. ReturnsforserviceshouldbemadetoyourDa-Litedealer. [. . . ]