User manual DA-LITE WM-VC INSTALLATION SHEET E-466

[. . . ] Concrete or brick walls require special fasteners and anchors. keep in mind you will need at least 2-3/8" between the ceiling and the top of the wall mount bracket to be able to position the case on the bracket. mount the screen case on the wall bracket as shown in figure 1. be sure the case is fully seated on the bracket. [. . . ] This provides structural stability to the case. be sure the ceiling has adequate reinforcement to attach a hook anchor. The top of the screen case has two channels with threaded nuts that slide the length of the case. attach ceiling hook brackets as provided to the screen case as shown in figure 3. The brackets can be attached anywhere within 12" of the end of the case. attach an s-hook or similar fastener to the hole in the bracket. 2 CeIlIng hook bRaCkeT 1/4 x 5/8" flaT head sCReW 1/4 x 5/8" flaT head sCReW sToP sCReW 6-3/8" Wall mounT bRaCkeT 2-5/16" Case 2-9/16" hook 5-11/16" FIGURE 1 CeIlIng mounT bRaCkeT FIGURE 2 FIGURE 3 ELECTRICAL INSTALLATION Internal wiring has been completed at the factory. Installer must route power to the wall switch and to the junction box located on the left end of the screen case. standard installation is for a single 120VaC or 240VaC wall switch to control the screen. optional Control units may have been ordered. Wiring diagrams for the built-in VPI and low voltage control are included in these instructions. Refer to additional instructions for the external VPI, external low voltage control, sCb-100 and sCb-200. baCk of Wall fRonT of sWITCh Wall sWITCh uP sToP doWn Red blaCk 5/12 VolT sCReen TRIggeR on PRoJeCToR 4 TENSIONEd CONTOUR® ELECTROL® INSTALLATION Rj-14 PIN-OUTS (TAB IS FACING UP) WHITE GREEN RED BLACK BUS (RP DATA) RQ DATA +5V GND 120V WIRING DIAGRAM WITH OPTIONAL BUILT-IN LOW VOLTAGE CONTROL Rj-22 jACK LED UP LIMIT TACTILE BUTTON UP Rj-22 PIN-OUTS (TAB IS FACING UP) +12V BUS (RP DATA) RQ DATA +5V GND RQ CLOCK BLUE YELLOW GREEN RED BLACK WHITE Supplied Rj-14 cable Rj-22 OUTPUT Standard Rj-22 can be used in place of Rj-14 Rj-22 INPUTS Rj-22 jACK UP DOWN COMMON BUS 5V Rj-45 RECEPTACLE Rj-45 PIN-OUTS DRY CONTACTS BUS (TAB IS FACING UP) MANUAL 2 +12V BUS (RP DATA) RQ DATA +5V GND RQ CLOCK BROWN BLUE YELLOW GREEN RED BLACK ORANGE PURPLE STO P DOW Rj-45 jACK 5V COM BUS N DOWN LIMIT TACTILE BUTTON BUS DATA CABLE MANUAL 1 FRONT OF WALL SWITCH BACK OF WALL SWITCH POWER WIRE 3-conductor 20-24 gauge wire can be used in place of the supplied RJ-14 cable to connect the wall switch. Connect the bus terminals on the wall switch to the corresponding bus terminals on the splitter board. IMPORTANT NOTE: The wall switch is ReQuIRed to make any limit switch adjustments, eVen if a third party control system is used. Therefore, it is advised to wire the switch or provide a 3-conductor connection that is accessible. GREEN (GROUND) BLACK (HOT) WHITE (COMMON) POWER INPUT 120VAC / 60HZ GROUND­MUST BE CONNECTED TO BUILDING GROUND 240V WIRING DIAGRAM WITH OPTIONAL BUILT-IN LOW VOLTAGE CONTROL BLUE (COMMON) BROWN (HOT) 240VAC 50HZ GREEN OPTIONAL IR AND RF REMOTE CONTROL LOW-VOLTAGE WALL SWITCH UP DN UP GND +5V MOTOR Rj9 Rj9 STOP DOWN 3-POSITION SWITCH Rj9 GROUND TO CASE UP +5V COM DN GROUND­MUST BE CONNECTED TO BUILDING GROUND GREEN FRONT BACK SPLITTER DRY CONTACTS ILT Rj9 PIN-OUTS (TAB IS FACING UP) IR or UP GND COMMON +5V DN or DATA BLACK RED GREEN WHITE IMPORTANT NOTE: The wall switch is ReQuIRed to make any limit switch adjustments, eVen if a third party control system is used. Therefore, it is advised to wire the switch or provide a 4-conductor connection that is accessible. 5 TROUBLESHOOTING Visit www. da-lite. com/products/tutorials. php to find installation and troubleshooting tutorials. You will also find a link to Live Chat for interactive support and you can contact us by email at info@da-lite. com or by phone at (800) 622-3737 or (574) 267-8101 with any troubleshooting questions. SYMPTOM 1. SOLUTION (a) Verify 115-125V (or 220-240V). If insufficient voltage, rewire incoming electric line. "Down" Position Check for power across black and white leads. "Up" Position Check for power across red and white leads. (b) blown fuse. (d) no power to operating switch or junction. Power at junction box (e) Thermal overload tripped. [. . . ] warrants its products to the original purchaser only, to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser provided they are properly operated according to da-lite's instructions and are not damaged due to improper handling or treatment after shipment from the factory. This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered with or repaired by a person other than authorized da-lite personnel. da-lite's sole obligation under this warranty shall be to repair or to replace (at da-lite's option) the defective part of the merchandise. Returns for service should be made to your da-lite dealer. [. . . ]