User manual DAEWOO 1500M

[. . . ] Turn off all controls before unplugging. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present. This appliance is intended for household use only and not for commercial or industrial use. Do not operate the vacuum if : - the power cord is damaged. [. . . ] 9 TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 SAVE THESE INSTRUCTIONS 2 3 R1500M-RICCAR-12142004. 12. 1411:50AM 5 DESCRIPTION AND OPERATION FULL BAG INDICATOR · If the red indicator appears: - Empty the vacuum bag. - If the vacuum bag isn't full and the full bag indicator is red, check the hose for a clog. · When cleaning with a tool (dusting brush, upholstery tool, crevice tool, floor tool), the red indicator may appear. In this case, continue cleaning. HOSE ADAPTER · When separating the hose from the body, pull the hose adapter while pressing the buttons. CORD REWIND ON/OFF SWITCH Adapter button HOSE HANDLE SUCTION CONTROL HIGH POWER CONTROL LOW POWER NOZZLE SWITCH ON OFF · 3n1 multi-purpose tool Insert end of wand into either end of tool for multiple cleaning functions. HARD SURFACE FLOOR TOOL Dusting Brush CLEANING TOOLS Upholstery Tool Crevice Tool STORAGE · Insert the brush holder on the neck of the wand into the groove. · For use on tile, hard wood, and linoleum floors. Petite Power Nozzle 4 5 R1500M-RICCAR-12142004. 12. 1411:50AM 7 HOW TO USE POWER NOZZLE OPERATION 1. Turning on the Power Nozzle The power nozzle can only be turned on if the canister is also turned on (canister on / off switch is located on the main body). The power nozzle on / off switch is located on the handle. Simply press the switch forward to engage the power nozzle. Using the Power Nozzle To achieve best cleaning results, slowly pass the power nozzle back and forth over the carpet or floor. Remove / Insert the Wand From The Power Nozzle Removing the wand from the power nozzle allows you to use the cleaning tools for baseboard or ceiling cleaning. To do this first turn the power nozzle and canister off. Then, press the nozzle release button and pull the wand out. To reinsert the wand into the power nozzle, simply press the back into the neck of the power nozzle. The wand will then "click" back into place. DIAGRAM 1 REAR VIEW OF POWER WAND AND NOZZLE ASSEMBLY Handle Wand Extension Grip (to extend wand) Telescopic Wand Power Nozzle DIAGRAM 2 FRONT VIEW OF POWER WAND AND NOZZLE ASSEMBLY Handle On/Off Control Wand Release Button Wand Extension Grip (to extend wand) Telescopic Wand Nozzle Release Button Power Nozzle 6 7 R1500M-RICCAR-12142004. 12. 1411:50AM 9 SAFETY PRECAUTIONS This vacuum cleaner should be used for normal, dry household dust and dirt. The manufacturer cannot be held responsible for any damage caused by use or operation of the vacuum contrary to these instructions. If the vacuum is wrongly operated for a purpose other than that for which it is intended, no liability can be accepted for any possible damage. REPLACING VACUUM BAG & FILTERS REPLACING THE VACUUM BAG Full Bag Indicator · Do not vacuum areas which contain moisture or water, flammable matter, needles, pins, razor blades, matches, cigarettes, etc. , since they may damage the vacuum or vacuum bag. · When rewinding the power cord, hold the plug before pressing the cord rewind button to prevent the cord from whipping. Dust Cover Vacuum Bag Holder · Turn canister off, remove · Pull the shutter of the vacuum bag. · Hold the cover while removing the vacuum bag from the vacuum bag holder. · Insert the new bag. NOTE: We recommend the vacuum bag is changed when indicator is RED or suction power is weak. The dust cover will not close without a bag in the unit or if the bag is not properly inserted. REPLACING THE FILTERS · Make sure a vacuum bag and filters are always inserted. [. . . ] · If clogged or blocked, remove the object. · Insert it completely. NOTES · The vacuum does not work. · Is the hose adapter inserted into the suction opening of the vacuum completely?· When the vacuum bag is full or any of the accessories are blocked, the over-heating protection for the motor is activated. · Switch off and unplug the vacuum. Check the vacuum bag and accessories and remove any blockages. [. . . ]