User manual DAEWOO 20H1T annexe 1

[. . . ] GB INSTRUCTION MANUAL 14H1T, 14H2T, 14H2TEG 14H2TBL, 20H1T, 20H2T GB14H1T, GB14H2T, GB14H2TEG GB14H2TBL, GB20H1T, GB20H2T CUSTOMER SERVICES HELPLINE 01189 252 577 100 WORTH knowing Please keep the televideo machine's guarantee card and receipt safe for warranty purposes. Precautions x Read carefully through this manual to familiarise yourself with this high quality televideo. x Make sure the rating of your household electricity supply matches that shown on the back of the televideo. x Refer to this chapter and the "Initial installation" chapter to help you install and adjust your televideo. Do not. . . x expose the televideo to high levels of humidity and heat, to avoid the risk of fire and electric shock. x open the televideo. Have a qualified technician carry out repairs. x connect the televideo to the power supply if you have just moved it from a cold to warm environment. [. . . ] If you wish to make changes : Move to the position you want to change using the VW CB buttons. Change the setting using the VW buttons. PDC(VPS) If a programme starts late or runs over, programme delivery control PDC(VPS) makes sure it gets recorded. In rare cases, poor reception or a fault at the TV station may stop PDC(VPS) from working properly: if this happens, set PDC(VPS) to `NO' when you programme the timer. Allow a few extra minutes recording when PDC(VPS) is off. Your television guide might show a PDC(VPS) start time different to the normal programme start time; be sure to enter PDC(VPS) start time. Auto tracking If you press the 0/ATK key in Playback mode, the televideo will operate the auto tracking function again. x If you wish to record from a satellite receiver select under "Pr" the satellite programme location or AV (depending on the connection with the aerial cable or a SCART cable. ) NB : Leave the satellite tuner switched on and to the programme you want to record. 11 RECORDING cassettes x For timer recordings, clock, date, and stations must be set correctly (page 5). x Load a cassette with its safety tab in place (see page 13) and with sufficient free space for the recording. Timer recording using VideoPlus+ (ShowView): (Option) Showview Call the VideoPlus+ (ShowView) menu. 13:57 --------01/01/2001 0-9 CLEAR SV/V+ : Digit entry : Store : Delete : Exit From your TV magazine, type in the number next to the programme you want to record. (Digit key) Confirm ( button) x Showview : FRANCE/CONTINENTAL x VideoPlus+ : U. K. Date Start End 01 05 14:18 17:15 --- --- --:-- --:---- --- --:-- --:----- --- --:-- --:----- --- --:-- --:----- --- --:-- --:--- PDC SP/LP Off SP Off SP Off SP Off SP Off SP Off SP If you press the button, Timer Programme menu will be displayed. If you want to change data, Press VW buttons. Confirm ( button) VW : Select CB : Access MENU : Previous CLEAR: Delete : Store (Do not use the main power button on the front panel of the set. ) The televideo will switch on and off automatically to record the timer event. x If you have not set the clock, when you press the VideoPlus+(Showview) button to set timer recording, the set will automatically change to the "CLOCK" menu. x If you don't have the VideoPlus+(Showview) numbers see page 11 for the normal timer. x If you have made a mistake, move back to the relevant position with the C button and change the setting. x During recording you can switch the screen off by pressing button. x The screen will indicate if the station is not programmed (page 5~7). x Should programmings overlap, you get a warning. x In the case of error messages, correct the input or check the date and time on your televideo (also check your TV guide). 12 x Your televideo automatically sets an electronic marker (index) at the beginning of each recording and timer recordings. It is these markers which are detected by the index function. M o r e FUNCTIONS INDEX +/F FF 00:12:34 INDEX 02 Pr 01 ARTE Clock 12:34 Press the button depending on the number of recordings (index marks) that you wish to wind forward. Press the button depending on the number of recordings (index marks) that you wish to wind backwards. 3x for 3 recordings back. G REW 00:12:34 INDEX -02 Pr 01 ARTE Clock 12:34 Resetting the counter to zero M REC 00:00:00 Pr 01 ARTE Clock 12:34 Press C-RESET button to reset the counter to 0 : 00 : 00 After you have finished recording pressing the C-ØSTOP button will cause the televideo to wind to the position 0 : 00 : 00 and stop. G REW 00:12:34 Go to zero Pr 01 ARTE Clock 12:34 Mute Pressing the mute button once turns the sound off. The sound returns if button is pressed once more The mute maintains when you press Pr VWor buttons. Child lock Child lock Enter number to lock ---- 0-9 CLEAR MENU : Digit entry : Store : Delete : Previous Choose "Miscellaneous" from the "menu". You can prevent use of the Televideo without the remote controller. The set is child locked after you input any secret number subsequently the TV picture will be overlaid with the child lock (OSD) On Screen Display and the sound will be muted. [. . . ] (The AV socket on this machine is the scart socket at the rear) Set the other video machine to playback and your Televideo machine to record. To record onto another VCR picture and sound of the selected station or recording is always available on the EURO AV scart socket. On the other video, select its AV input and set the machine to record. Switch your televideo to playback at the position you want copying to start. 17 Connections and ASSEMBLING Scart socket This is used to connect : a VCR a CAMCODER and a video game console or satellite TV receiver or DVD. [. . . ]