User manual DAEWOO AD13 & KOT MODELS

[. . . ] Phillips screwdrivers, Electric Drill Motor, 1/2" & 5/8" Wood Bits & 3/16" Drill Bit, Saw to cut exhaust opening, (if needed) or Jig Saw, Tin Snips (if needed), Pencil , Tape Measure, Paper Tape & Duct Tape. II. The Top Cabinet Template, used to locate the power cord clearance hole, cabinet mounting holes and the vertical exhaust location. The following is a list of parts you may need for installing your Over-the-Range microwave oven. You will find them packaged inside the microwave cooking cavity. Remove all parts from the oven cavity and compare them with the parts list and illustration to be sure that none are missing Important Safety Information Grounding Instructions This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of the electric shock by providing an escape wire for the electric current. [. . . ] Using a hammer, tap lightly across the mounting surface to find a solid sound. After locating the stud(s), the center can be found by: Probing the wall with a small nail to find the edges of the stud and then placing a mark half way between the edges. The center of any adjacent studs should be 16" from this mark. CAUTION: FOR PERSONAL SAFETY THIS PRODUCT CANNOT BE INSTALLED TO CABINET ARRANGEMENT'S SUCH AS AN ISLAND OR A PENINSULA. IT MUST BE MOUNTED TO BOTH A TOP CABINET AND A WALL. Air Director Rear Exhaust Log screws (part #1) must be installed in these area Hood Exhaust Duct Outside ventilation requires HOOD EXHAUST DUCT. EXHAUST CONNECTION: The hood exhaust has been designed to mate with a standard 3-1/4" x 10" rectangular duct. REAR EXHAUST: If rear or horizontal exhaust is to be used, care should be taken to align exhaust with space between studs, or wall should be prepared at the time it is constructed by leaving enough space between wall studs to accommodate exhaust. MAXIMUM DUCT LENGTH: For satisfactory air movement, the total duct length of 3-1/4" x 10" rectangular should not exceed maximum 1foot. Step. 2 (For Recirculation Only) *Roll the Ventilation Director so that the Rear opening area is closed. *Align the Ventilation Director's Hole A to D and B to C. *Tighten the screws. A F B D E C WALL DUCT 3 4 Install the Mounting Plate Step. 1 Setup position Draw a line down the middle of the studs( See the Wall Construction, page 3 ) Draw a vertical line on the wall at the center of the 22. 2" wide space. PEN CUT OUT THIS AREA Mounting microwave oven NOTE: IT IS VERY IMPORTANT THAT THIS OVEN BE INSTALLED BY TWO PEOPLE. PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. * Read the instructions on the TOP CABINET TEMPLATE * Tape it underneath the top cabinet * Drill the holes, following the instructions on the template NOTE: TOP CABINET TEMPLATE instruction must be complete to proceed. Attach the mounting plate on the wall, making sure that the mounting plate mate to the bottom of the cabinet, and place the mounting plate with the center line drawn on the wall. Step. 2 Cut out exhaust outlet (For Rear Exhaust Only) a. Attach the mounting plate against the rear wall at the position the microwave oven installed. b. Using the pencil, draw the outline of the cutout area as figure. This will give the location and size of the rectangular cutout for the rear wall duct. * Make sure the exhaust adaptor is squared up in the house duct and line up with holes in the mounting plate. * Attach the 28" foam tape to the back of the mounting plate around the exhaust opening where it will touch the wall. Step. 1 Protect the top of your range by placing a portion of the carton or some other heavy material over the cooking surface before mounting your oven. A FOAM TAPE Step. 2 Hang the unit on the two tabs at the bottom of the mounting plate. [. . . ] Recirculation Ventilation System Your over the range microwave oven has NOT been provided with a charcoal filter for a recirculation venting application. The charcoal filter must be required Contact your authorized dealer. Ventilation Director See the page 4, Ventilation Director, step 2 Charcoal Filter Install the Mounting plate See the page 5, Install the mounting plate. * You need not perform the step2 ; Horizontal ventilation only. Step. 5 Dress power cord nearly in top cabinet. [. . . ]