User manual DAEWOO DE-K6121D-KS3

[. . . ] 1280 HR TIME LAPSE RECORDER WITH 40 HR REAL TIME REC User's Guide EV-VCR960 EJECT REC Be sure to read carefully and follow all the SAFETY INFORMATION on page i. Keep the manual in a safe place for future reference. P/N : 97P95600D0-R8 Worth Knowing Please keep the video machine's guarantee card and receipt safe for warranty purposes. Precautions x Read carefully through this manual to familiarize yourself with this high­quality Time Lapse video cassette recorder. x Make sure the rating of your household electricity supply matches that shown on the back of the Time Lapse video cassette recorder. x Refer to this chapter and the "Initial installation" chapter to help you AUTO SET CH. OP EJECT install and adjust your Time Lapse video cassette recorder. expose the Time Lapse video cassette recorder to high levels of humidity and heat, to avoid the risk of fire and electric shock. open the Time Lapse video cassette recorder. [. . . ] Press the SHIFT (or ) button, until the cursor is located in the setting to correct. Press the SET ­ (or +) button, to correct the setting. · Press the MENU button three times until the normal screen is displayed. 2 3 4 Press the POWER(STANDBY/ON) button. · If the cassette tape is ejected while timer recording is set, the buzzer will be heard 5 times (when the buzzer function is set to "YES". ) 18 Time Lapse Video Cassette Recorder Time Lapse Video Cassette Recorder 19 Alarm Recording Alarm Recording Setting Alarm recording is performed when there is an input (trigger) at the ALARM IN terminal, " " is displayed on the display panel. 2 Press the MENU, SHIFT , SHIFT buttons in sequence to display the REC MODE SET menu . 3 Press the SHIFT button until the arrow mark () points to ALARM REC SET. 4 Press the SHIFT button to display the ALARM REC SET menu. · Auto / 20sec / 30sec / 40sec / 01min / 02min / 3min / 5min / 10min / 15min / 20min / 25min / 30min : Recording for the set duration. (min : minute) · T. END : Records until the tape end is reached when there is alarm trigger input. · Alarm Counter Reset can be performed by pressing the CLEAR key in "Alarm Time" of Initial Menu screen. Alarm Recording Counter Display During alarm recording, " " will be flashing on the display panel. The maximum display number of alarm triggers is "35", at the next alarm recording the counter will indicate "00". Connecting to a Monitor for Normal Recording · During alarm recording all buttons are disabled except the STOP button. If the STOP button is pressed, the alarm recording will stop. · If an alarm trigger is received while alarm recording is in progress, the recording duration for the second alarm will be calculated from that point. · When there is a power loss during alarm recording, if the power is restored within the recording set duration, alarm recording will continue. · When you select `Alarm Duration' as 20sec, 30sec, 40sec or 1min, alarm search error may happen. Therefore confirm it in `Alarm TIme' menu and scan it. 5 Press the SHIFT button to select "YES" or "NO". · YES . . The alarm recording takes place when there is alarm trigger input · NO . The alarm recording does not take place 6 7 · · · · Press the SHIFT button to set the Alarm speed. Press the SHIFT button to select the desired recording speed. 3H . 30­hour mode recording ALARM ALARM 2 3 8 9 Press the SHIFT button to set the alarm duration. Press the SHIFT button to select the desired recording duration. · Auto : Records as long as the alarm signal is being input. (Minimum 2 minutes is recorded. ) 20 Time Lapse Video Cassette Recorder Time Lapse Video Cassette Recorder 21 Panic Recording Connecting to a Monitor for Alarm Recording This feature is similar to an alarm recording, but the recording time is not pre­selected. When there is a panic input at the PANIC IN Terminal, recording will start and continue for up to 3 hours. Series Recording Using 2 VCRs or more, the series recording function lets you switch recording from one unit to the next (only with VCRs of the same model as this one). Series Recording Setup ALARM ALARM 2 3 1 2 Connect 2 VCRs or more as illustrated on next page. Set the following items as indicated. VCR No. 1 · During series recording, autorepeat recording or timer recording are not possible. · If in the REC MODE SET menu, "Series Rec Set" is set to "NO", series recording will not be possible. Item VCR No. 2 and on Cassette tape Loaded Loaded Operation mode Stop Stop Repeat Rec Set "NO" "NO" Series Rec Set "YES" "YES" Timer recording OFF (not set) OFF (not set) Security lock switch (SET LOCK switch) "OFF" "ON" 3 Press the REC button on VCR No. 1. · Recording will start in series recording mode. 22 Time Lapse Video Cassette Recorder Time Lapse Video Cassette Recorder 23 Autorepeat Recording 4 Set the security lock on VCR No. 1. · When the end of the tape on VCR No. 1 is reached, the output at the SERIES OUT terminal will switch signal. This will start recording on VCR No. 2, the tape will stop and be ejected on VCR No. 1. Autorepeat Recording The same tape can be recorded over many times. [. . . ] ­ Be sure to select "YES" for autorepeat recording. ­ Set "YES" again for autorepeat recording. ­ Set the date and time correctly. "NO" is selected for autorepeat recording in the REC MODE SET menu. During autorepeat recording when there is an alarm input, autorepeat recording is canceled. [. . . ]