User manual DAEWOO DLM-42U1

[. . . ] 48586701E101-R2 LCD TELEVISION INSTRUCTION MANUAL DLM-42U1(FH/FHM/GPB/GUB/UPB/UUB) DLM-42U2(FH/FHM/GPB/GUB/UPB/UUB) DLM-46U1(FH/FHM/GPB/GUB/UPB/UUB) DLM-46U2(FH/FHM/GPB/GUB/UPB/UUB) Caution CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. 2 Important Safeguards Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. 1. [. . . ] · The skipped program number will be displayed as red in the EDIT menu. Edit Pr 91 92 93 94 95 96 97 98 99 00 Ch. - -- -- -- -- -- -- -- -- -- -Pr 01 02 03 04 05 06 07 08 09 10 Ch. - -- -- -- -- -- -- -- -- -- -Pr 11 12 13 14 15 16 17 18 19 20 MENU Ch. - -- -- -- -- -- -- -- -- -- -- Position Skip Move Exit Delete 30 Selection of AV and Multimedia Input Signal When watching video, Camcorder, DVD, Cable TV with AV - See page 12 for connection method of Camcorder and Video. - When pressing " " button on the TV set, screen changes as follows: TV => AV1 => AV2(S-Video) => PC => HDMI1 => HDMI2 => MMP(Option) => Component => TV 1. Pressing the "AV/COMP/MMP" button on the remote controller. · The screen changes as follows: AV1 => AV2(S-Video) => Component => MMP(Option) => AV1 Note : Cautions in menu setup · Don't connect the composite video signal to AV2 and S-video signal to the S-video input at the same time. If connecting both signals at the same time, the S-video takes precedence. · If sound signal is mono only, connect it to the L-terminal of the sound input terminal. 31 Selection of AV and Multimedia Input Signal When connecting PC, STB, DVD with Multimedia 1. Pressing the "HDMI/PC" button on the remote control. · The screen changes as follows: PC => HDMI1 => HDMI2 => PC HDMI & PC mode 1. For optimum picture quality, 1920 x 1080P on FULL HD TV model computer or set top box output at a 60Hz refresh rate. Using other formats or refresh rates may result in reduced picture quality. If the message `No signal' appears on the screen, adjust the PC output to a format listed in the Multimedia Input table. Note : · 1280 X 720 mode is commonly used for Component. · So if this mode is used at PC mode, the screen can be enlarged. 32 Screen Adjustment When setting up various screen modes - The user may select various screens designed for a good picture without adjusting the brightness, contrast or colour individually. Pressing the "PICTURE" button. · The screen changes as follows: Normal => Movie => Dynamic => Favourite => Normal · The screen adjustment status changes as the following screens are displayed sequentially whenever pressing the "PICTURE" button. · The screen returns to the mode prior to turning the power off when you power on again. Note : · Normal : For a highly defined image in a normally bright room. · Dynamic : For a clear-cut image emphasising high contrast for sports viewing. · Favourite : Allows the user to customise settings as desired. 33 Screen Adjustment When adjusting the screen to taste - You can enjoy various screens by adjusting Brightness, Contrast, Colour, Sharpness, etc to the user's taste. 1. Select "PICTURE" by pressing the "MENU" button. · The menu screen appears as follows. Picture Screen Sound Function Install 2. [. . . ] Pressing the "HOLD" button again, the current subpage appears. CALLING UP SUBPAGE DIRECTLY Pressing the "SUBPAGE" button ( ) , " - - - - " appears. Enter the subpage number that you want to call up with the "NUMBER" button, for example, the 2nd page, sequence 0002. The desired subpage will eventually be displayed on the screen and holds it there. [. . . ]