User manual DAEWOO DLP-3212L

[. . . ] LCD TELEVISION INSTRUCTION MANUAL DLP-2612 DLP-3212 DLP-2612L DLP-3212L Caution CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING:To reduce the risk of fire or electric shock hazard, do not expose this appliance to rain or moisture. 2 Safety Precautions 1. CLEANING Unplug this TV equipment from the AC power outlet before cleaning. [. . . ] Select a programme number you want to tune finely with the PR buttons. Select the Fine Tune from the Install menu. Press the VOL button and the fine tuning window appears. Adjust the fine tuning with the VOL buttons. If you press down blue button, Fine Tune will be canceled. Note : If you are unable to get a good picture or sound because of a poor broadcasting signal, adjustment of the fine tuning might improve it. Fine Tune Pr : 01 00 Adjust Cancel Menu : Save 20 Basic Operation Switching On and Off SWITCHING ON 1. If the Indicator is not lit, then the TV set is powered off. You must press the On/OFF button on the TV set. The set will switch to stand-by mode and then the Indicator will illuminate in Red. Press the POWER( ) button on the remote controller or the POWER( TV set when the indicator is red. The TV set will be switched on and the indicator will be changed to green. Press the POWER( ) button on the remote controller or the POWER( ) button on the TV set to return the set to its stand-by mode. Press the On/OFF button on the TV set to switch the TV set off completely. NOTE: If you turn the TV off, the present time that you have set will disappear. If you don't use the set for extended periods of time, unplug the AC cord from Power outlet. Recall The Recall button on the remote controller is used to display the current status; Mode (TV, Video, Component, PC), Signal information, the Programme number, MGDi, and PIP information, Time are displayed. Information Source Signal MGDi Clock : : : : TV Pr Pal Off No -- -- : -1 PIP/POP : 21 Basic Operation Programme Selection The set has 99 programme numbers, PR01. . PR99. The Number buttons are used for direct programme selection. To select a two-digit programme, press the second numbered button within 2 seconds. When you want to select PR10, you should press down "1" and "0" within 2second. If you only press down "1", after 2second, PR1 will be selected. ) PR SELECTION You can also select a programme by pressing step by step the PR buttons. Sound Control VOLUME CONTROL Adjust the volume with the MUTE Pressing the MUTE( ) button turns the sound off. The sound returns if the button is pressed once more. Stereo/Mono/Dual1, 2 sound selection When receiving a Stereo programme, Stereo mode is automatically selected. In Stereo reception if you are unable to get good sound quality due to poor reception, you can force a change from Stereo to Mono transmission by pressing the ( ) button. Then the program status display indicates Mono. [. . . ] Pressing the HOLD button again, the current subpage appears. 34 Menu Operation CALLING UP SUBPAGE DIRECTLY Pressing the SUBPAGE button ( ) , " - - - - " appears. Enter the subpage number that you want to call up with the NUMBER button, for example, the 2nd page, sequence 0002. The desired subpage will eventually be displayed on the screen and holds it there. Meanwhile whilst you are waiting, it is possible to go back to the TV picture by pressing the CANCEL button( X )on the remote and after a while, press the CANCEL button again to revert back to the saved Teletext sub page. [. . . ]